Installing the base station | Siemens 2011 instruction

18.7.99

kap18.fm5

Gigaset 2011 Comfort, GBR: A30852-X1106-B307-1-

Important notes on putting into service and operation

Important notes on putting into service and operation

Installing the base station

Installation site/installation area

●A 220/230 V AC power socket must be located at the installation site.

●In order to avoid interference, the base station should not be in the direct vicinity of other electronic equip- ment such as Hi-fi, office or microwave equipment.

●Place the base station on a flat, non-slip surface. Un- der normal circumstances, the rubber feet will not leave marks. However, due to the vast array of surface finishes applied to furniture, marks on the installation surface cannot be entirely ruled out.

●Radio transmission between the base station and handsets complies with the DECT standard. Gigaset 2011 thus observes all relevant European regulations. However, if there is interference to the picture or sound of your satellite equipment, consult your spe- cialist satellite dealer.

●Depending on ambient conditions, the maximum ra- dio range between the base station and the handset is approx. 300 m outdoors, and approx. 50 m indoors. If the range warning is activated for the handset

(➔ page 56), a signal will sound when you move out- side the radio range.

Temperature/ambient conditions

●The base station is designed for operation in protect- ed areas with a temperature range from +5 °C to +45° C.

●The base station should not be installed in damp are- as (such as bathrooms or laundry rooms), close to heat sources or in direct sunlight.

85

Image 96

Siemens 2011 operating instructions Important notes on putting into service and operation, Installing the base station

Contents

Gigaset 2011 Comfort Gigaset Your guide to this manual Overview Gigaset Overview keys Base station keys Display keys assignments @, and # Overview display symbols Symbol Explanation Safety precautions Installation instructionsOnly use rechargeable bat As shown Approval and conformity Contents Contents Short cuts Step by step guide to putting into service Step by step guide to putting into serviceObserve the safety precautions Check the contents of the package Underside of base station housing Power cordTelephone cord Charge the batteries Checking your own telephone’s signalling method Setting dial pulsing@33x Menu-driven operation Menu-driven operationMenu structure Menu structure is hierarchical Moving to higher menu levels and exiting a menu Activating the additional menu Handset Settings Beeps Confirm Beep Displays in the operating instructionsAbbreviated presentation XW t New Entry Handset Volume Menu-driven operation On-line menuExample of menu operation during a telephone call Following is displayed Menu-driven operation Principal menus Main menu Handset LockDirectory menu Redial menu Settings Beeps Key BeepsRange Beep Language On/off/protected mode You can switch your handset To protected mode Off On againSwitching the handset to protected mode Operating modes When the handset is switched off Switching off the handset Operating modes Signalling method Incoming calls Incoming callsCall number display When the handset is in the base station or charging unit Accepting callsInternal call Following example shows a call from mobile unit Incoming calls External call-waiting during internal calls Ending a callDeactivating the microphone mute function External outgoing calls External outgoing callsCalling external parties Suppressing secret numbers for redial Suppressing call number display at the called partyNo answer or line busy Manually inserting a pause External outgoing calls Redial Dialling with the directoryRepeating the last number dialled Repeating one of the last five call numbers T Dial Number Dialling from the call list Dial Number When a caller is selected, Current date, time, number White PeterActivating the call list Selecting and calling back a caller Deleting a callback party from the call list Gigaset 2000SSearching for and dialling a callback number Gigaset 1000C Switch to Tone Search for a call number in the list Delete the entry External outgoing calls Ending a call Collective ringing and internal calls Collective ringing and internal callsMaking collective calls from one handset to all handsets Making internal calls Ending an internal call Internal consultation calls and transferring calls Internal consultation calls and transferring callsConsultation calls Either Disconnect the internal party Creating and managing the directory Creating and managing the directoryUW t e.g. New Entry Saving an entry or cancelling an operation Save Entry Cancel Inserting a pauseNew Entry U W t New Entry Copying numbers Deleting the directory Delete Entry T Delete Entry Processing and saving an entryXW t Delete Directory Creating and managing the directory Available memory Copying an entry/directoryXW t Available Memory T Copy Entry Administering the redial memory Administering the redial memory Copying a redial number to the directory You can copy a selected call number to the directoryCopy Number Displaying the call number T Display Number Contents input field Input functionInput function Entering names and numbers Moving from the Name field to the Content field ExceptionInserting, deleting, and moving characters Deleting Example making a new directory entry Examples changing an entryMaking changes in the Name field Procedure Making changes in the Contents field Entering letters, special characters, and digits Example field boundaries123 789 Character set Key Press x Important basic settings Important basic settingsChanging the base code/PIN Changing the handset PIN If you forget your base code or PIN Reset the base station to the factory default Backlighting Baby alarm level Language setting Isdn configuration Select ServicesDSS number, redial Handset PIN stored page 44 is not delet- ed Important basic settings Operating in a telephone system Possible signalling method settings@37x Dual-tone multifrequency signalling DTMF/Flash @33x Set dial pulsing DP Entering the analog trunk and the MSI Service Analog trunks Modify the pause length after the analog trunk/MSI @24 x SET @2% x SET @2@ x SET @21 x SETDeleting the analog trunk/MSI Redial 2%3 u SET Individual base station settings Individual base station settingsSwitch the ringer off and save the setting Setting the base station ringer tone Redial 411x SET Redial 41@x SET Individual handset settings Individual handset settingsSetting the handset volume Settings t Handset Volume Individual handset settings Ringer settings OK or Isdn configuration Settings Handset Settings Auto BacklightSave. Symbol for on = Automatic call acceptance Handset Settings Beeps Key Beeps Activating/deactivating the battery low beepActivating/deactivating the key beep Quit the menu without saving any changes Handset Settings Beeps Range Warning Handset Settings BeepsActivating/deactivating the error beep Activating/deactivating the range warning beep Baby alarm Individual handset settings Baby alarm level Selecting a languageGerman English French Individual handset settings Select services Select services listActivating and deactivating select services Loading the select services list provided Call duration display is activated by default Displaying call durationDisplaying call duration Activating/deactivating call duration display Emergency calls when the system is locked Gigaset 2011 lock functionsGigaset 2011 lock functions Activating/deactivating the lock for outgoing calls Number stored Example emergencyNumber 110 stored Deleting all emergency numbers Service #8 % Gigaset 2011 lock functions Barred numbers for handsets Deleting all barred numbers Service Extensions, are shown on the display Example handsets 1, 2, and 3 are registered1u SET @u SET Set Outward-restricted trunk access Lock functions on the handset Lock functions on the handsetActivating/deactivating the handset lock Barred numbers for handsets Handset lock is switched on 66, an error tone is outputDisplay with locked handset Display with system lock Settings t Register Registering a Gigaset 2000C handset at a base stationX OK Prepare the base station De-registering a handset from a base station Switching between collective call and ring priority Service Operating more than one handsetOperating more than one handset Call allocation for incoming calls Excluding or including a handset from/into collective call Selecting a handset for ring priorityConfirm Setting the number of rings for ring priority Service Naming handsetsExample 3 rings are set Firm Operating at more than one base station Operating at more than one base station Setting the preferred or fixed station Select BaseSelect Best Base and press OK to confirm Select the base station Operating at more than one base station Base station names De-registering a base station Short cuts Short cutsDescriptions with example Short cut menu Short cuts New entry T New EntryFunction list Insert Function Insert Function SET Key Insert Function Base Prompt SET KeyDisplaying a function T Show Function Saving a short cut Cancelling a procedure Cancel Checking for double entries T Check DuplicateEditing an entry Deleting an entry Short cuts Displaying an entry Deleting all entriesT Display Entry Short Cut u W t Delete Memory Short cuts Copying an entry/memory T Copy Memory Default short cuts T DefaultShortCutsShort cuts Starting a short cut T Start Short cuts Short cut list For handset and base functions Important notes on putting into service and operation Important notes on putting into service and operationInstalling the base station Installation site/installation area For users who wear hearing aids Nickel-cadmium Nickel-metal-hydride Important notes on putting into service and operation Handset battery life Battery charging timesFitting the carrying clip on the handset Maintenance Gigaset 1000C Or a ServiceDifferences in operation Gigaset 2000C Free Standard Most manufacturers for Dect radio transmissionStand-by approx W Use approx W Warranty Symptom Cause Remedy Contact person Base code entered does not Ring tone Tuuuuut Recall TuuuuutInternal dial tone Tuuut Almost empty Special accessories Special accessoriesGigaset 1000TAE Gigaset 2000L Special accessories Gigaset 2000S Gigaset 2000THeadset Quick reference guide handset Gigaset 2000C Quick reference guide handset Gigaset 2000C Index 100 101 Warranty Users Calling external parties Making internal calls102 Issued by Private Communication System Group Hofmannstraße 51, D-81359 MünchenSiemens AG