Manuals / Brands / Computer Equipment / Network Router / Sierra Wireless / Computer Equipment / Network Router

Sierra Wireless 20070914 Configuring the Raven at the Polling Host for Modbus on UDP

1 171

Download 171 pages, 3.15 Mb

Configuring Modbus/BSAP

Rev 3.0B Feb.08 74

TheremoteRaventhendisassemblesthepacketbeforetrans‐

mittingtheRTUIDandserialdatatotheremoteunit.The

remoteunitsoperateinnormalUDPmodeandtheirdatais

senttothehostviatheremoteRavenandhostRaven.

Configuring the Raven at the Polling Host for Modbus on UDP

ThissectioncoversaPollingHostwithstandardModbus,

variationsmayneedadditionalATcommands.

1. Configure the listening/device ports

InAceManager,selectMiscinthesidemenu.

Figure 8-1: AceManager: Misc

Thedestinationportforthemodematthehostneedstomatch

thedeviceport(*DPORT)inuseonallthemodemsatthe

remotesites.Forexample,iftheremotemodem’sdeviceport

(*DPORT)is“12345”,thentheModbushostmodemʹsS53

destinationportshouldbesetto“12345”.

Take noteof(orset)theDevicePortsettingin*DPORTto

configurethedestinationportontheremotemodems.

Contents

Main Important Notice Safety and Hazards Limitation of Liability Patents Copyright Trademarks QUALCOMM 3G Contact Information Revision History Contents Activating your Raven on the TELUS Network . . . . . . . . . . . . . . . . . . . . . . . . .19 Data Communication and Host Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 SNMP : Simple Network Management Protocol . . . . . . . . . . . . . . . . . . . . . . .82 Rev 3.0B Feb.08 4 Rev 3.0B Feb.08 5 Rev 3.0B Feb.08 6 Page 1: Introduction to the Raven ALEOS AceWare Connecting to the TELUS Network 1x Communication ALEOS AceWare AceManager Page AceNet AceView Page Modem Doctor USB Connecting to the TELUS Network Dynamic vs. Static IP Addresses 1x Communication 2: Specifications Interface Port Pin-Outs Power Connector Interface Port Pin-Outs Power Connector 3: Activating your Raven on the TELUS Network Setup Wizard Activating Using AT Commands Setup Wizard 1. Starting the Setup Wizard 2. Connecting to the Modem 3. Selecting Tasks 4. Optional:Update ALEOS 5. Activate Modem Page 6. Test Modem Setup 7. Optional: Setting up a DUN Connection Page Activating Using AT Commands Page Page 4: Hardware Installation of the Raven Connecting to Power Connecting to a Computer or other Device Indicator Lights Mounting Page Page Page 5: Configuring your Raven Using AceManager Using Templates Using a Terminal Application with AT Commands Using AceManager 1. Start AceManager 2. Connect to your Raven 3. Enter the configuration options 4. Write the changes to the modem Using Templates 1. Creating the Template with AceManager Page 2. Applying a Template to one modem with AceManager 3. Optional: Applying one template to several modems simultaneously with AceNet Page Using a Terminal Application with AT Commands 1. Choose a name and icon for your connection. 2. Connect To 3. Port Sett ings (serial o nly) 4. Connected AT Commands 6: Data Communication and Host Modes Basic Modes Serial Modes Data Communication Basic Modes Start up Mode AT M ode PassThru Mode Te ln et M od e Serial Modes PPP Page SLIP UDP and UDP Pad Page TCP an d TCP Pad Hybrid Modes Page Data Communication Public and Private Mode Keepalive Page Page 7: IP Manager Understanding Domain Names Using IP Manager with your Raven Understanding DNS Understanding Domain Names Dynamic Names Using IP Manager with your Raven Data Usage for IP Manager Server Updates Eairlink.com Understanding DNS Configuring DNS The PPP-Peer Domain Name 8: Configuring Modbus/BSAP Modbus Overview Page Configuring the Raven at the Polling Host for Modbus on UDP 1. Configure the listening/device ports Page 4. Optional: Dynamic IP Address Configuring the Remote Ravens for Modbus with UDP 1. Configure the ports 2. Configure IP addresses for the host. 3. Configure the default mode for start-up. 4. Configure other RTU settings. 5. Optional: Dynamic IP Address Page Page 9: SNMP : Simple Network Management Protocol SNMP Configuration SNMP MIB Definition Sample Management Information Base (MIB) SNMP Traps SNMP Configuration Listening Port Security Level User Name and Password Trap Destination Community String SNMP MIB Definition Sample Rev 3.0B Feb.08 86 Rev 3.0B Feb.08 87 Rev 3.0B Feb.08 88 Rev 3.0B Feb.08 89 Display Responses Object AT Com man d phoneNumber *NETPHONE? deviceID *DEVICEID? electronicID I3 aleosSWVer I1 Rev 3.0B Feb.08 90 Product ID A A: Configuration Commands Info (information) Information Displayed in AceManager without AT Commands Listed Status Page Information Displayed in AceManager without AT Commands Listed AT Commands Requiring PassThru mode Page Common Misc (Miscellaneous) Page Page Page Serial Page Page Page Page TCP Page UDP Page Page DNS Dynamic IP Page PPP/Ethernet Page PassThru Page Page Page Page Page Other Page Page Frie nds Logging Telemetry/Addr List Page Addr List 1x/EV-DO Page Page Page B B: Circuit Switch Communications Step by Step Configuration Step by Step Configuration Configuring Circuit-Switch AT Commands and the Command String Page Raven LEDs in Circuit-Switched Mode Step by Step Configuration 1. Gather the required information, hardware, a nd software 2. Connect the modem to your computer 3. Erase the internal memory Page 4. Activate the Raven 5. Start AceManager. 6. Configure serial port speed. 7. Save the serial setting. 8. Configure the Raven using a AceManager template. Page Page 14. Commission the Raven Modem on Site. Page C C: Windows Dial-up Networking (DUN) Installing a modem driver for Raven 1. Connect the Raven. 2. Install the driver. Page Page Page Page Creating a Dial-Up Networking (PPP) Connection 1. Create a new network connection. Page Page Page Page Page Page Page Page Connecting to the Internet Using DUN AceView 1. Start AceView. 2. Enable the Connection. Windows DUN 1. Start the DUN session. 2. Select Dial to connect to the modem and the cellular network.