SMC Networks SMC6826MPE Mounting

NSTALLING

THE

WITCH

3-4

Mounting

This switch can be mounted in a standard 19-inch equipment rack or on a

desktop or shelf. Mounting instructions for each type of site follow.

Rack Mounting

Before rack mounting the sw itch, pay particular attention to the following

factors:

• Temperature: Since the temperature within a rack assembly may be

higher than the ambient room temperature, check that the

rack-environment temperature is within the specified operating

temperature range. (See page C-2.)

• Mechanical Loading: Do not place any equipment on top of a

rack-mounted unit.

• Circuit Overloading: Be sure that the supply circuit to the rack

assembly is not overloaded.

• Grounding: Rack-mounted equipment should be properly grounded.

Particular attention should be given to supp ly connections other than

direct connections to the mains.

To rack-mount devices:

1. Attach the brackets to the device using the screws provided in the

Bracket Mounting Kit.

Contents

Main TigerStack III 10/100 Port Fast Ethernet Swi 24- tch Installation Guide Page Page Page L W IMITED ARRANTY L W IMITED ARRANTY ii C FCC - Class A Japan VCCI Class A Industry Canada - Class A ii CE Mark Declaration of Conformance for EMI and Safety (EEC) iii Australia AS/NZS 3548 (1995) - Class A Safety Compliance Power Cord Safety iv Veuillez lire fond l'information de la scurit suivante avant d'installer le Switch: v Bitte unbedingt vor dem Einbauen des Switches die folgenden Sicherheitsanweisungen durchlesen: vi Warnings and Cautionary Messages vii War nin gs (in German) Environmental Statement End of Product Life Span Manufacturing Materials Page ABLE OF ix ONTENTS 1 About the TigerStack III 10/100 . . . . . . . . . . . . . . . . . . .1-1 C x 4 Making Network Connections . . . . . . . . . . . . . . . . . . . . 4-1 APPENDICES: xii ABLES F xiii IGURES Page Page T III 10/100 1-2 Switch Architecture O 1-3 Network Management Options Description of Hardware H 1-5 Port and System Status LED Indicators T III 10/100 1-6 H 1-7 Figure 1-3 System LED Indicators Table 1-2 System Status LED Indicators Page Page Features and Benefits Page Page HAPTER 2-1 2 N P ETWORK LANNING Introduction to Switching Application Examples Supplying PoE StackingCable E 2-3 Collapsed Backbone ... ... P ETWORK SwitchUnits ... ... LANNING E PPLICATION RPS 24 14 P 2-6 Making VLAN Connections N 2-7 Application Notes Page HAPTER 3-1 3 I S THE NSTALLING Ethernet Cabling Equipment Checklist Mounting 3-5 S THE NSTALLING WITCH 3-7 Desktop or Shelf Mounting S 3-8 Installing an SFP Transceiver S 3-9 Stacking Switches Installing a Stacking Transceiver S Slave THE NSTALLING Page S 3-12 Connecting to a Power Source Connecting to the Console Port Page Page Page Page N C 4-4 Network Wiring Connections -P D Wall PatchPanel AIR N C 4-6 Fiber Optic Devices R Connectivity Rules N C Table 4-3 Maximum 1000BASE-LX Gigabit Ethernet Cable Length 4-8 1000BASE-T Cable Requirements Cable Labeling and Connection Records Page A-1 ROUBLESHOOTING Diagnosing Switch Indicators Table A-1 Troubleshooting Chart A-2 Diagnosing Power Problems with the LED Indicators Power and Cooling Problems A-3 Installation In-Band Access Stack Troubleshooting B-1 B ABLES Twisted-Pair Cable and Pin Assignments B-2 10/100BASE-TX Pin Assignments -P A Figure B-2 Straight-throug h Wiring IN P B-4 Crossover Wiring Page B-6 F S B-7 Fiber Standards Page C-1 APPENDIX C S Physical Characteristics C-2 Switch Features F C-3 Management Features Standards C-4 Compliances Page Page Glossary-1 G Glossary-2 Glossary-3 Glossary-4 Glossary-5 Page I NDEX Index-1 Numerics A I L M N O T W