Menu items in the range 700 to 799, relating to video control (continued)
Item number | Item name | Settings |
| |
743 | PR LEVEL (HD) | Adjust the PR level of the |
| |
|
| OUTPUT connector. |
| |
|
| 0.0% (0H) to 100% (800H) to 141.3% (B4EH) |
| |
|
|
|
| |
745 | SETUP LEVEL (HD) | Adjust the setup level of the |
| |
|
| OUTPUT connector. |
| |
|
| 0 to 110H to 220H |
| |
|
|
|
| |
746 | SYNC PHASE (HD) | Control the H sync phase of the |
| |
|
| OUTPUT connector according to the menu. |
| |
|
| 0 to 80H to FFH |
| |
|
|
|
| |
747 | SYNC PHASE FINE (HD) | Fine control the H sync phase of the |
| |
|
| HDSDI OUTPUT connector according to the menu. |
| |
|
| 0 to 3FFH |
| |
|
|
|
| |
| Menu items in the range 800 to 899, relating to audio control |
| ||
|
|
|
|
|
Item number | Item name | Settings |
| |
801 | DIGITAL JOG SOUND | Turns the digital jog sound on and off. |
| |
|
| OFF: Digital jog sound is turned off. |
| |
|
| Audio of digital channels not subjected to speed correction is output. When the |
| |
|
| tape stops, after one second the audio is muted. |
| |
|
| ON: Digital jog sound is turned on. |
| |
|
| When the tape speed is in the range |
| |
|
| and the same jog sound as a conventional analog VTR is output. |
| |
|
|
|
| |
802 | DIGITAL AUD MUTING IN | Set the digital audio muting conditions during shuttle playback. |
| |
| SHUTTLE MODE | OFF: Not muted. |
| |
|
| CUEUP: Muted during cueup or preroll operations. |
| |
|
| FULL: Muted in shuttle mode. |
| |
|
|
|
| |
803 | DIGITAL AUDIO FADE | Specify the time for |
| |
| TIME | 5ms, 10ms, 15ms, 20ms, 25msa), 50msb), 85ms, 115msc) |
| |
|
|
| ||
|
|
|
|
|
|
| Note |
| |
|
| The |
| |
|
| the OUT point for the length specified by this setting. Even at the minimum 5ms |
| |
|
| setting, a length of recording corresponding to a field is rewritten. |
| |
|
| To avoid rewriting, set menu item 317 “AUDIO EDIT MODE” to “CUT”. In this case |
| |
|
| there is an audio discontinuity at the edit point. There is no effect on the recorded |
| |
|
| video signal. |
| |
|
|
|
| |
805 | AUDIO MONITOR | Select the audio mixing method used for digital audio signals supplied to the |
| |
| OUTPUT MIXING | MONITOR OUTPUT connector. |
| |
|
| ADD: Simple addition |
| |
|
| RMS: |
| |
|
| AVE: Simple average |
| |
|
|
|
| |
806 | LEVEL METER SCALE | Select the digital audio level display mode. |
| |
|
| PEAK0: Display the audio level as negative values with the maximum level set to |
| |
|
| “0 dB”. |
| |
|
| REF.0: Display the audio level as positive and negative values with the reference |
| |
|
| level set to “0 dB”. |
| |
|
|
|
| |
807 | AUDIO OUTPUT PHASE | Select the output timing of digital audio playback signals (HDSDI, SDI and AES/ |
| |
|
| EBU only). The reference position is 80H; when the setting is less than 80H, the |
| |
|
| output timing is advanced, and when it is higher than 80H, the output timing is |
| |
|
| delayed. (at 80H, 128 samples = approx. 2.7 ms, and 1 sample = approx. 20 µs) |
| |
|
| 0 to 80 to FF: Set in this range. |
| |
|
|
|
|
|
Menus Setup 9 Chapter