4-3-5 Selecting the Drop Frame Mode (DF/NDF)

Press the [F9] (DF/NDF) button to select the running mode for the CTL counter and the time code generator.

DF: Drop frame mode1) (DF is displayed.)

NDF: Non-drop frame mode2) (NDF is displayed.)

auto: The unit switches to drop frame mode when the field frequency is 29.97 Hz, and switches to non-drop frame mode when the field frequency is 30 Hz.

1)Drop frame mode

In order to compensate for differences between time code values from the time code generator and the actual time that occurs when the frame frequency of this unit is 29.97 Hz, the drop frame mode causes the time code generator to omit the first two frames (frame 00 and 01) in each minute except the tenth.

2)Non-drop frame mode

In this mode, drop frame mode processing is not performed. Since there is no frame cutting, a discrepancy of about 86 seconds occurs each day in the case of a frame frequency of 29.97 Hz.

Notes

This setting is only active when the frame frequency of the unit is 29.97 Hz or 30 Hz.

When the [F7] (TCG MODE) button is set to “regene”, the drop frame mode is inoperative since the time code generator is synchronized to the playback time code.

4-3-6 Selecting the Content of the

Second Time Code Display Area

(TC2 SEL)

Select the content of the second time code display area using the [F10] (TC2 SEL) button.

Setting

Time data displayed

OFF

No display

 

 

LTC

LTC value read from the time code reader

 

 

Auto

When the playback speed is within the range ±1/2

 

normal speed, then VITC, and if outside this

 

range then the LTC is displayed.

 

 

VITC

VITC value read from the time code reader

 

 

CTL

CTL signal count value

 

 

UBR

User bits read by the time code reader (LTC)

 

 

UBV

User bit value read from the time code reader

 

(VITC)

 

 

TCG

Value generated by the time code generator

 

 

UBG

User bits value generated by the time code

 

generator

 

 

When the two-unit editing display, a warning, or similar is shown, the second time code display area does not appear.

For details about the warnings, see “Warning Messages” on page 135.

4-3-7 Selecting CTL Display Mode

(TAPE TIMER)

Press the ALT/[F1] (TAPE TIMER) buttons to select a 12- hour or 24-hour clock for the CTL display.

+–12H:12-hour clock 24H: 24-hour clock

4-3-8 Presetting Pulldown Time Code (PDPSET MENU)

(when HKSR-5001 is installed)

To preset the pulldown time code when this VTR is operated in 23.98PsF/24PsF mode, use the following procedure.

3

4

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

21

1Press the TC button, then press the ALT button.

You can also press the ALT and TC buttons simultaneously.

2Press the [F2] (PDPSET MENU) button. The PDPSET menu appears.

P R E S E T

 

 

 

M O D E

I N T R P

D F

F 2

 

 

 

P D T I M E

 

2 4 F

 

00H 00M 00S 00F

2 4 F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S E T

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I N T R P

D F

2 F O

 

 

 

00H00M 00S 00F

 

 

3 0 F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P D T C

 

 

 

 

 

E X I T

 

 

 

D F / N D F

 

 

 

 

 

 

 

 

N D F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 Press the [F1] (PRESET MODE) button to select 24F or 30F time code to be preset.

Settings Menu 4 Chapter

4-3 TC Menu 61