CHAPTER 1
Rear Panel Features
1 | 2 | 3 | 4 | 5 | 6 | 7 |
MANUFACTURED UNDER LICENSE |
|
|
|
|
|
|
|
|
|
FROM DOLBY LABORATORIES. |
|
| AUDIO/VIDEO INPUTS |
|
| AUDIO/VIDEO OUTPUTS | |||
"DOLBY", |
|
|
|
| |||||
|
|
|
| ||||||
| DVD | SAT | VID1 | VID2 | VCR | CD | MAIN | VCR VID2/MON2 | |
TRADEMARKS OF DOLBY | S | ||||||||
LABORATORIES. |
|
|
|
|
|
|
|
| |
VIDEO |
|
|
|
|
|
|
|
| |
Made in Snohomish, Washington, U.S.A.
RIGHTRIGHT
COMPONENT VIDEO IN | COMPONENT | TRIGGERS SURROUND | MAIN | CENTER | ||
DVD | SAT | VID1 | MAIN OUT MON2 | 12VDC |
|
|
Y
LEFT | LEFT |
MAIN | SURROUND |
8
9
10
FM |
|
|
|
|
|
|
|
|
|
|
|
|
75 Ω |
|
|
|
|
|
|
|
|
|
|
|
|
COMP | DVD | SAT | VID1 | VID2 | VCR | CD |
| MAIN | VCR | VID2/MON2 | ||
VIDEO |
|
|
|
|
|
|
|
|
|
|
| |
GND |
| DVD | SAT | VID1 | VID2 | VCR | CD |
| MAIN | VCR | VID2/MON2 | |
|
|
| ||||||||||
AM | L |
|
|
|
|
|
| L |
|
|
|
|
| R |
|
|
|
|
|
| R |
|
|
|
|
MANUFACTURED UNDER LICENSE |
|
|
|
|
|
|
|
|
|
|
|
|
FROM DIGITAL THEATER SYSTEMS, |
|
|
|
|
|
|
|
|
|
|
|
|
INC. US PAT. NO. 5,451,942, |
| AUDIO INPUTS | AUDIO OUTPUTS |
|
| |||||||
5,956,674, 5,974,380, 5,978,762 AND |
|
| ||||||||||
OTHER |
|
| ||||||||||
ISSUED AND PENDING. "DTS", |
| PHONO | DAT | TAPE | DAT | TAPE |
| LEFT | L SUR | CEN | LB SUR | |
|
|
|
|
|
|
|
|
|
|
|
| |
AND "NEO:6" ARE TRADEMARKS |
|
|
|
|
|
|
|
|
|
|
|
|
OF DIGITAL THEATER SYSTEMS, | L |
|
|
|
|
|
|
|
|
|
|
|
INC. COPYRIGHT 1996, 2000, |
|
|
| L |
|
|
|
|
|
|
| |
DIGITAL THEATER SYSTEMS, INC. |
|
|
|
|
|
|
|
|
|
| ||
ALL RIGHTS RESERVED. |
|
|
|
|
|
|
|
|
|
|
|
|
| R |
|
|
| R |
|
|
|
|
|
|
|
|
| PHONO | DAT | TAPE | DAT | TAPE |
| RIGHT | R SUR | SUB | RB SUR | |
|
|
| Cr |
| MAINZONE | 12VDC |
|
|
| Cb |
| ZONE2 | 12VDC |
DIGITAL AUDIO INPUTS |
|
|
| |||
DVD | SAT | VID1 | CD | DVD | SAT | VID1 |
|
|
| ||||
|
|
|
| CD | DAT | VID2 |
STEREO OUTPUTS |
|
| LINE LEVEL AUDIO OUTPUTS | |||
FIXED MAIN ZONE2 |
| LEFT | LEFT SUR | CENTER | SUB2 | |
|
| L |
|
|
|
|
|
| R |
|
|
|
|
FIXED MAIN ZONE2 |
| RIGHT | RIGHT SUR | SUB1 | SUB3 | |
SPEAKER LEVEL AUDIO OUTPUTS
| Sunfire | |
|
| |
Ultimate Receiver II | ||
| DIGITAL OUT | IEEE |
|
| 1394 |
LB SUR | SIDES | I R |
L SIDE AXIS | MAIN | |
|
| REPLACE WITH ORIGINAL |
|
| FUSE TYPE AND RATING |
RB SUR | R SIDE AXIS | ZONE2 |
AC FUSE
SURROUND
RIGHT BACK LEFT
OPTIONAL:
OR
ZONE2
AC INPUT
120 VAC 
60 Hz
1112
1.Audio/Video Inputs
These audio,
2. Audio/Video Outputs
MAIN: connects to the inputs of a TV monitor, where the video of any selected input and the On Screen Display (OSD) can be viewed. The audio connec- tions allow you to listen to any selected audio source through your TV’s speakers.
VCR: connects to the inputs of a VCR to allow recording.
VID2/MON2: connects to the input of a second VCR for recording, or to a second TV. When con- Þgured in the OSD for “VID2,” this output is muted whenever the VID2 input is selected. This prevents feedback; also there is no OSD then on this output. When conÞgured for “MON2,” the output is always active, the same as the Main output.
12
13 | 14 15 | 16 |
Note: Analog audio signals are present at these L and R outputs even if a digital input has been selected. The output is a 2 chan- nel downmix if the digital source is more than 2 channels.
3. Component Video In
These inputs connect to the component video outputs of your DVD, SAT or other video source (VID1) if they have this advanced capability. When these inputs are selected, the Receiver's Pro- cessor will automatically route any video signals going into these jacks to the component video outputs. Note that component video provides the best picture compared to composite or
4. Component Video Out
If your TV Monitor has component video inputs, connect them to these outputs. If you select DVD, SAT or VID1, then any video sig- nals going to the component inputs, will pass through to your TV monitor.
17 1819 20 21
5. Triggers and Relay
The relay switch is normally open, and it will close after a short delay, when selecting a source. This can be used in installations to trigger video screen deployment, or other custom purposes. The OSD INPUTS menu lets you choose which inputs activate the relay.
The +12 VDC outputs are on whenever their zone is enabled. They can be used to automatically turn on ampliÞers for example. The 1/8”
6. Speaker-level Outputs
These
User's Manual
