Installing an Expansion Card | SUPER MICRO Computer 5017P-TLN4F

Chapter 6: Advanced Chassis Setup

6-6 Installing an Expansion Card

The SC504 chassis includes a PCI slot for an optional full-height, half-length ex- pansion card. A riser card is required in order to connect the expansion card to the motherboard. For further information on expansionon cards and risers cards, visit the Supermicro website at www.supermicro.com

Expansion Card

Clip

Figure 6-4. Locating the Expansion Card Clip

Installing the Expansion Card

1.Power down the server, disconnect the power cord from the power supply and remove the cover. Locate the expansion card clip on the back of the chassis

2.Remove the screws holding the expansion card clip and the PCI slot cover which covers the PCI slot opening in the back of the chassis.

3.Remove the expansion card clip and the PCI slot cover from the chassis.

Expansion Card Clip

PCI Slot Cover

Riser Card Slot

Figure 6-5. Installing the Expansion Card and Riser Card

6-7

Image 56

SUPER MICRO Computer 5017P-TLN4F, 5017P-TF user manual Installing an Expansion Card, Locating the Expansion Card Clip

Contents

Super Manual Revision Release Date July 19 About This Manual Manual Organization Bios Advanced Serverboard SetupAdvanced Chassis Setup Preface Table of Contents System Safety Bios Chapter Introduction Overview Motherboard Features Processors MemorySerial ATA PCI Expansion Slots Server Chassis Features System PowerHard Drive Subsystem Front Control Panel Intel QM77 Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-PacificPage Unpacking the System Preparing for SetupChoosing a Setup Location Rack Precautions Server Precautions Ambient Operating Temperature Rack Mounting Considerations Installing the System into a Rack Installing the Chassis into a Standard Rack Installing the Chassis into a Telco Rack Telco RackPage Control Panel Buttons ResetPower Power Fail Control Panel LEDsInformational LED Status Description Drive Carrier LEDs HDDPage Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Chapter Advanced Motherboard Setup Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel Control Panel Header Pins Rear I/O Ports Installing Memory How to Install SO DIMMsOnboard Processor and Heatsink Adding PCI Add-On Cards SO Dimm Socket To Remove Motherboard Details X9SPV-LN4F/F-3610ME Layout X9SPV-LN4F/F-3610ME Quick Reference Connector DescriptionJumper Description Default Setting Connector Definitions Power ConnectorsPower Button Reset Button Power On LED NMI Button Ethernet Ports Fan HeadersChassis Intrusion Serial Ports LAN Ports LAN1~LAN4 Internal SpeakerUniversal Serial Bus USB Overheat/Fan Fail LED Power LED/SpeakerSgpio Headers DOM Power Connector Power Supply SMBus I2C Header Jumper Settings Bios Write Protect JWP1Explanation of Jumpers Cmos Clear USB Wake-Up JPUSB1 Watch Dog Enable/DisableBMC Enable/Disable Onboard Indicators Standby Power LED LED1LAN LEDs Ipmi Heartbeat LED LED2 Sata and SAS Ports Serial ATA Ports Installing Software Driver/Tool Installation Display Screen SuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Control Panel Front and Rear Chassis Views Removing the Chassis Cover Removing the Chassis Cover Installing Hard Drives System Fans Optional Installing 2.5 Hard Drives Hard Drive Configuration Options Installing Hard Drives Installing an Expansion Card Locating the Expansion Card Clip Installing the Expansion Card Power Supply Replacing the Power SupplyPage Introduction Starting Bios Setup UtilityHow To Change the Configuration Data Main Setup How to Start the Setup Utility System Time/System Date Supermicro X9SPV-F/LN4FProcessor System Memory Advanced Setup Configurations BOOT FeatureQuiet Boot Bootup Num-Lock Processor and Clock Options Hardware Prefetcher Available when supported by the CPU Active Processor CoresLimit Cpuid Maximum Clock Spread Spectrum CPU PPM Configuration Power Technology Turbo ModeConfig TDP Lock Long Duration Power Limit Advanced Chipset Control System Agent SA Configuration PCH-IO Configuration Xhci Pre-Boot Driver Xhci ModeHS Port #1~#4 Switchable USB Ports Per-Port Disable Control IDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings IDO Request Enable Available when supported by the hardware Target Link Speed Available when supported by the hardware Compliance SOS Available when supported by the hardware Is Disabled Network StackPCI-E Slot 1 Option ROM Onboard LAN Option ROM Select Super IO Device Configuration Serial Port 1 Settings / Serial Port 2 SettingsIpv6 PXE Support Auto Remote Access Configuration Console Redirection Settings Recorder Mode ResolutionLegacy OS Redirection Resolution Redirection After Bios Post Console Redirection Settings for EMS ACPI ConfigurationHigh Precision Timer Out-of-Band-Mgmt Port ISCSI Configuration Trusted Computing ConfigurationIntel Txtlt Configuration Change Attempt Order Add an AttemptDelete Attempts Port Configuration Information Event LogsLink Speed Wake On LAN Change SmBIOS Event Log Settings System Event Log Ipmi SettingsWhen SEL Full BMC Network Configuration Update Ipmi LAN ConfigurationConfiguration Source Log EFI Status Codes Boot Security Settings Administrator PasswordUser Password HDD Password Save Changes and Reset ExitDiscard Changes and Exit Discard Changes Restore Defaults Save As User DefaultsRestore User Defaults Boot Override Appendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front