Appendix a Post Error Beep Codes | SUPER MICRO Computer 5017P-TLN4F

Appendix A: POST Error Beep Codes

Appendix A

POST Error Beep Codes

This section lists POST (Power On Self Test) error beep codes for the AMI BIOS. POST error beep codes are divided into two categories: recoverable and terminal. This section lists Beep Codes for recoverable POST errors.

Recoverable POST Error Beep Codes

When a recoverable type of error occurs during POST, BIOS will display a POST code that describes the problem. BIOS may also issue one of the following beep codes:

1 long and two short beeps - video configuration error

1 repetitive long beep - no memory detected

1 continuous beep with the front panel Overheat LED on - system overheat

1 continuous beep with the front panel Fan Fail LED blinking - fan failure

8 short beeps - display memory read/write error

A-1

Image 90

SUPER MICRO Computer 5017P-TLN4F, 5017P-TF user manual Appendix a Post Error Beep Codes, Recoverable Post Error Beep Codes

Contents

Super Manual Revision Release Date July 19 About This Manual Manual Organization Advanced Serverboard Setup Advanced Chassis SetupBios Preface Table of Contents System Safety Bios Chapter Introduction Overview Serial ATA Motherboard FeaturesProcessors Memory PCI Expansion Slots Hard Drive Subsystem Server Chassis FeaturesSystem Power Front Control Panel Intel QM77 Chipset System Block Diagram Europe Contacting SupermicroHeadquarters Asia-PacificPage Preparing for Setup Choosing a Setup LocationUnpacking the System Rack Precautions Server Precautions Ambient Operating Temperature Rack Mounting Considerations Installing the System into a Rack Installing the Chassis into a Standard Rack Installing the Chassis into a Telco Rack Telco RackPage Reset PowerControl Panel Buttons Informational LED Status Power FailControl Panel LEDs Description Drive Carrier LEDs HDDPage Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Chapter Advanced Motherboard Setup Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel Control Panel Header Pins Rear I/O Ports Onboard Processor and Heatsink Installing MemoryHow to Install SO DIMMs Adding PCI Add-On Cards SO Dimm Socket To Remove Motherboard Details X9SPV-LN4F/F-3610ME Layout Connector Description Jumper Description Default SettingX9SPV-LN4F/F-3610ME Quick Reference Power Button Connector DefinitionsPower Connectors Reset Button Power On LED NMI Button Chassis Intrusion Ethernet PortsFan Headers Serial Ports Internal Speaker Universal Serial Bus USBLAN Ports LAN1~LAN4 Power LED/Speaker Sgpio HeadersOverheat/Fan Fail LED DOM Power Connector Power Supply SMBus I2C Header Explanation of Jumpers Jumper SettingsBios Write Protect JWP1 Cmos Clear Watch Dog Enable/Disable BMC Enable/DisableUSB Wake-Up JPUSB1 LAN LEDs Onboard IndicatorsStandby Power LED LED1 Ipmi Heartbeat LED LED2 Sata and SAS Ports Serial ATA Ports Installing Software Driver/Tool Installation Display Screen SuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Control Panel Front and Rear Chassis Views Removing the Chassis Cover Removing the Chassis Cover Installing Hard Drives System Fans Optional Installing 2.5 Hard Drives Hard Drive Configuration Options Installing Hard Drives Installing an Expansion Card Locating the Expansion Card Clip Installing the Expansion Card Power Supply Replacing the Power SupplyPage Starting Bios Setup Utility How To Change the Configuration DataIntroduction Main Setup How to Start the Setup Utility Processor System Time/System DateSupermicro X9SPV-F/LN4F System Memory Quiet Boot Advanced Setup ConfigurationsBOOT Feature Bootup Num-Lock Processor and Clock Options Limit Cpuid Maximum Hardware Prefetcher Available when supported by the CPUActive Processor Cores Clock Spread Spectrum Config TDP Lock CPU PPM Configuration Power TechnologyTurbo Mode Long Duration Power Limit Advanced Chipset Control System Agent SA Configuration PCH-IO Configuration HS Port #1~#4 Switchable Xhci Pre-Boot DriverXhci Mode USB Ports Per-Port Disable Control IDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings IDO Request Enable Available when supported by the hardware Target Link Speed Available when supported by the hardware PCI-E Slot 1 Option ROM Compliance SOS Available when supported by the hardwareIs Disabled Network Stack Onboard LAN Option ROM Select Ipv6 PXE Support Super IO Device ConfigurationSerial Port 1 Settings / Serial Port 2 Settings Auto Remote Access Configuration Console Redirection Settings Legacy OS Redirection Resolution Recorder ModeResolution Redirection After Bios Post High Precision Timer Console Redirection Settings for EMSACPI Configuration Out-of-Band-Mgmt Port Trusted Computing Configuration Intel Txtlt ConfigurationISCSI Configuration Add an Attempt Delete AttemptsChange Attempt Order Link Speed Port Configuration InformationEvent Logs Wake On LAN Change SmBIOS Event Log Settings Ipmi Settings When SEL FullSystem Event Log Configuration Source BMC Network ConfigurationUpdate Ipmi LAN Configuration Log EFI Status Codes Boot User Password Security SettingsAdministrator Password HDD Password Discard Changes and Exit Save Changes and ResetExit Discard Changes Restore User Defaults Restore DefaultsSave As User Defaults Boot Override Appendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front