SUPER MICRO Computer 5017P-TF, 5017P-TLN4F 7-10

7-10

SUPERSERVER 5017P-TLN4F/TF User's Manual

EHCI Hand-Off

This item is for Operating Systems that do not support Enhanced Host Con-

troller Interface (EHCI) hand-off. When enabled, EHCI ownership change

will be claimed by the EHCI driver. The settings are Enabled and Disabled.

XHCI Pre-Boot Driver

This feature enables support for the xHCI pre-boot driver. The options are

Enabled and Disabled.

XHCI Mode

Use this feature to select the xHCI controller mode of operation. The options

are Smart Auto, Auto, Enabled, and Disabled.

HS Port #1~#4 Switchable

This feature allows for HS port switching between xHCI and EHCI. When set

to Disabled, the specied port is routed to EHCI. The options are Enabled

and Disabled.

Note: If HS port is routed to xHCI, the corresponding SS port is enabled.

XHCI Streams

Use this feature to enable the maximum primary stream array size for xHCI.

The options are Enabled and Disabled.

EHCI1, EHCI2

This feature enables the EHCI interface (USB 2.0). At least one EHCI control-

ler must always be enabled. The options are Enabled and Disabled.

USB Ports Per-Port Disable Control

If set to Enabled, this feature allows deactivation of selected USB ports. The

options are Disabled and Enabled. If set to Enabled, the following will appear:

USB Port #0~#13 Disable

Select which USB ports to disable. The settings are Enabled and

Disabled.

Deep Sx (EUP)

Select Enabled to enable Deep Sleep State support. The settings are Enabled

and Disabled.

Contents

Main S Manual Revision 1.0 Release Date: July 19, 2012 Printed in the United States of America iii Preface About This Manual Manual Organization S UPER S iv Page vi Table of Contents Chapter 1 Introduction Chapter 2 Server Installation Chapter 3 System Interface vii Chapter 4 System Safety Chapter 5 Advanced Motherboard Setup Chapter 6 Advanced Chassis Setup Page Page 1-2 Motherboard Features 1-3 Server Chassis Features 1-4 SPI SATA 6Gb/s USB2.0 DDR3 (CHB) 1-4 Contacting Supermicro Headquarters Europe Asia-Pacic Page 2-1 Chapter 2 Server Installation 2-1 Overview 2-2 Unpacking the System Page Rack Mounting Considerations 2-4 2-4 Installing the System into a Rack Installing the Chassis into a Standard Rack 2-5 Telco Rack Installing the Chassis into a Telco Rack Page Page 3-2 3-3 Control Panel LEDs Power Fail NIC1 NIC2 3-3 Page Page 4-2 4-2 General Safety Precautions Page 4-4 4-4 Operating Precautions OR 5-1 Chapter 5 Advanced Motherboard Setup 5-1 Handling the Motherboard Precautions Unpacking 5-2 Connecting Power Cables Connecting the Control Panel 5-3 5-3 Rear I/O Ports 5-4 5-4 Onboard Processor and Heatsink 5-5 Installing Memory How to Install SO DIMMs Memory Support 5-6 Adding PCI Add-On Cards The SO DIMM Socket 5-6 5-7 Motherboard Details 5-7 X9SPV-LN4F/F-3610ME Quick Reference 5-8 5-8 Connector Denitions 5-9 5-10 5-11 5-12 5-13 5-14 5-9 Jumper Settings 5-15 5-16 5-10 Onboard Indicators 5-17 5-11 SATA and SAS Ports 5-12 Installing Software 5-19 SuperDoctor III Page Page 6-1 Chapter 6 Advanced Chassis Setup 6-1 Static-Sensitive Devices Precautions Unpacking 6-2 6-2 Control Panel Page 6-4 6-4 System Fans (Optional) 6-5 Installing Hard Drives 6-5 6-6 Hard Drive Conguration Options 6-7 6-6 Installing an Expansion Card Page 6-9 6-7 Power Supply Replacing the Power Supply Page Chapter 7 BIOS 7-1 Introduction Starting BIOS Setup Utility How To Change the Conguration Data 7-2 7-2 Main Setup Page 7-4 7-3 Advanced Setup Congurations W arning 7-6 Page 7-8 Page 7-10 Page 7-12 Page 7-14 Page 7-16 Page 7-18 Page 7-20 iSCSI Conguration 7-22 7-4 Event Logs 7-24 7-5 IPMI Settings 7-26 7-6 Boot 7-28 7-7 Security Settings 7-8 Exit 7-30 Page Page Appendix B System Specications