Event Logs, Link Speed | SUPER MICRO Computer 5017P-TLN4F, 5017P-TF

Chapter 7: BIOS

Intel(R) 82579LM / Intel(R) 82574L Gigabit Network

Connection

NIC Configuration

Link Speed

Use this feature to select the link speed to be used. The options are AutoNeg, 10 Mbps Half, 10 Mbps Full, 100 Mbps Half and 100 Mbps Full.

Wake On LAN

Use this feature to activate the Wake On LAN (WOL) feature. The options are Enabled, and Disabled.

Blink LEDs (Range 0-15 seconds)

Please specifies the blink rate of the NIC LED. Select from 1-15 second in- tervals.

Port Configuration Information

This section displays the current configuration of the Network Interface.

7-4 Event Logs

7-1

Image 82

SUPER MICRO Computer 5017P-TLN4F, 5017P-TF user manual Event Logs, Link Speed, Wake On LAN, Blink LEDs Range 0-15 seconds

Contents

Super Manual Revision Release Date July 19 About This Manual Manual Organization Advanced Chassis Setup Advanced Serverboard SetupBios Preface Table of Contents System Safety Bios Chapter Introduction Overview Serial ATA Motherboard FeaturesProcessors Memory PCI Expansion Slots Hard Drive Subsystem Server Chassis FeaturesSystem Power Front Control Panel Intel QM77 Chipset System Block Diagram Europe Contacting SupermicroHeadquarters Asia-PacificPage Choosing a Setup Location Preparing for SetupUnpacking the System Rack Precautions Server Precautions Ambient Operating Temperature Rack Mounting Considerations Installing the System into a Rack Installing the Chassis into a Standard Rack Installing the Chassis into a Telco Rack Telco RackPage Power ResetControl Panel Buttons Informational LED Status Power FailControl Panel LEDs Description Drive Carrier LEDs HDDPage Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Chapter Advanced Motherboard Setup Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel Control Panel Header Pins Rear I/O Ports Onboard Processor and Heatsink Installing MemoryHow to Install SO DIMMs Adding PCI Add-On Cards SO Dimm Socket To Remove Motherboard Details X9SPV-LN4F/F-3610ME Layout Jumper Description Default Setting Connector DescriptionX9SPV-LN4F/F-3610ME Quick Reference Power Button Connector DefinitionsPower Connectors Reset Button Power On LED NMI Button Chassis Intrusion Ethernet PortsFan Headers Serial Ports Universal Serial Bus USB Internal SpeakerLAN Ports LAN1~LAN4 Sgpio Headers Power LED/SpeakerOverheat/Fan Fail LED DOM Power Connector Power Supply SMBus I2C Header Explanation of Jumpers Jumper SettingsBios Write Protect JWP1 Cmos Clear BMC Enable/Disable Watch Dog Enable/DisableUSB Wake-Up JPUSB1 LAN LEDs Onboard IndicatorsStandby Power LED LED1 Ipmi Heartbeat LED LED2 Sata and SAS Ports Serial ATA Ports Installing Software Driver/Tool Installation Display Screen SuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Control Panel Front and Rear Chassis Views Removing the Chassis Cover Removing the Chassis Cover Installing Hard Drives System Fans Optional Installing 2.5 Hard Drives Hard Drive Configuration Options Installing Hard Drives Installing an Expansion Card Locating the Expansion Card Clip Installing the Expansion Card Power Supply Replacing the Power SupplyPage How To Change the Configuration Data Starting Bios Setup UtilityIntroduction Main Setup How to Start the Setup Utility Processor System Time/System DateSupermicro X9SPV-F/LN4F System Memory Quiet Boot Advanced Setup ConfigurationsBOOT Feature Bootup Num-Lock Processor and Clock Options Limit Cpuid Maximum Hardware Prefetcher Available when supported by the CPUActive Processor Cores Clock Spread Spectrum Config TDP Lock CPU PPM Configuration Power TechnologyTurbo Mode Long Duration Power Limit Advanced Chipset Control System Agent SA Configuration PCH-IO Configuration HS Port #1~#4 Switchable Xhci Pre-Boot DriverXhci Mode USB Ports Per-Port Disable Control IDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings IDO Request Enable Available when supported by the hardware Target Link Speed Available when supported by the hardware PCI-E Slot 1 Option ROM Compliance SOS Available when supported by the hardwareIs Disabled Network Stack Onboard LAN Option ROM Select Ipv6 PXE Support Super IO Device ConfigurationSerial Port 1 Settings / Serial Port 2 Settings Auto Remote Access Configuration Console Redirection Settings Legacy OS Redirection Resolution Recorder ModeResolution Redirection After Bios Post High Precision Timer Console Redirection Settings for EMSACPI Configuration Out-of-Band-Mgmt Port Intel Txtlt Configuration Trusted Computing ConfigurationISCSI Configuration Delete Attempts Add an AttemptChange Attempt Order Link Speed Port Configuration InformationEvent Logs Wake On LAN Change SmBIOS Event Log Settings When SEL Full Ipmi SettingsSystem Event Log Configuration Source BMC Network ConfigurationUpdate Ipmi LAN Configuration Log EFI Status Codes Boot User Password Security SettingsAdministrator Password HDD Password Discard Changes and Exit Save Changes and ResetExit Discard Changes Restore User Defaults Restore DefaultsSave As User Defaults Boot Override Appendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front