System configuration, Menu | TANDBERG D12155-10 specification

TANDBERG Videoconferencing System	Installation

System configuration

•Switch the system on by activating the power switch on the codec (located on the right hand side at the rear of the codec). A green light is shown (located in the center on the front of the codec).

•After the system has performed a self-test routine, product logo and a ‘Welcome’ menu will be displayed on the monitor.

NOTE

THESE SETTINGS ARE ESSENTIAL FOR OPTIMAL SYSTEM SET-UP.

•Enabled but unused ISDN lines (lines not active) should be disabled. Select the Quick Key ‘System Info’ (on the remote control) to view line status.

menu

PRESS MENU ON THE REMOTE CONTROL. SELECT THE MENU ‘TERMINAL SETTINGS’, ‘NETWORK’, ‘ISDN-BRISETTINGS’. SELECT THE RELEVANT ‘LINE SETUP’ MENU AND SET ‘ENABLED: OFF’.

•Enter System Name to identify the system during an MCU conference. Select ‘Utilities’, ‘System Name’ and enter the name using the number keys (as on a mobile phone).

•Select the language you want to use in ‘Terminal Settings’, ‘Language’.

•If you are using two monitors, set ‘Utilities’, ‘Dual Monitor: On’.

•To activate MultiSite and/or Presenter, enter an option key (see paperwork accompanying your system), see

‘Terminal Settings’, ‘Software Options’.

connect • Press CONNECT on the remote control. A dial tone should be heard if the network is active.

• Using the monitor remote control, adjust the volume on the monitor to a level of your choice. This volume will be the default volume for all calls.

17

Image 17

TANDBERG D12155-10 user manual System configuration, Menu

Contents

UserManual Tandberg Videoconferencing System Trademarks and copyright Environmental Issues Operator Safety Summary Contents Appendices 104 Index 114 Advanced usePeripheral Equipment TIP Introduction LAN Menu structure At a glance the Tandberg 2500 system Tandberg 2500 Videoconferencing System Codec V.E. II CameraMonitors Cabinet Remote control Table microphone Unpacking InstallationPrecautions Page Power cable Connecting cablesMonitor cables Microphone cable 5a. Isdn cables using BRI interface Monitor configuration5b. Other networks using the External Network interface LAN cable Menu System configuration Isdn configuration LAN configuration Welcome menu Getting startedSystem start-up Basics Making a call Making and ending calls TIP Selecting / setting default quality bandwidth Selecting / setting default network Correcting keying mistakes Answer a callEnd a call Press D Irectory to bring up the following menu Directory Delete Entry Add New EntryEdit Entry Add Site Add MultiSite Entry General use Adjusting volumeView outgoing video selfview Microphone on/off On Screen Symbols Do Not Disturb / Sleep Mode Controlling the Main Camera Focusing cameraSelecting video sources Moving / zooming camera Voice Activated Camera Positioning Storing presets PresetsSelecting presets Far end camera control Fecc Sending a snapshot Sending and receiving snapshotsViewing a snapshot Receiving a snapshot Add Duo Video Duo Video End a Duo Video call MultiSite MCU MultiSite cascading Establishing MultiSite meetings using Directory Adding an extra site dial out Adding an extra site dial Disconnecting sites from a conference PC SoftPresenter PC Presenter Text Chat / Closed Captioning Web-interface Snapshots Other PC applicationsStreaming Main menu Menu PasswordAdvanced use Call quality Qcif Advanced call quality Duo Video Mode Presentation ModePresentations Duo Video Quality Duo Video / Snapshot Source Duo Video NumberAuto-Display Snapshot Snapshot Filter Autoanswer UtilitiesFar end camera control Dual Monitor Welcome Menu Auto-PIPContinuous Presence MCU status line Web Snapshots MCU services Quick Menu Release floor Request floorTerminal Names View site # Chair control Audio Inputs Audio SettingsPage Audio Outputs Level Settings Out1 +13.5dB Out2AUX Out3VCR Previous Menu Echo Control Page Automatic Gain Control AGC Settings Restore Audio Defaults Alert Tones & Volume Document Camera Video SettingsCamera Tracking Mode Brightness FocusWhitebalance Video Name VGA Settings VNC Settings Network Configuration Terminal Settings ISDN-BRI Settings Spids This Service has Limited Access on Some Isdn Networks Parallel dial External network settings 35/RS-366 cable LAN Settings Page Settings Page Rsvp Advanced H.323 Settings Diffserv QoS TypeIP Precedence IP Settings Snmp Settings Access Code Call SettingsIncoming MCU calls Incoming telephone calls Encryption Secure Conference Encryption Mode Network Profiles Max Call Length Dataport configuration Page Software Options Language Channel status DiagnosticsSystem info TIP Call status Restore defaults IP Address Conflict Check View current settingsTest subsystem Interfaces Peripheral Equipment E2 only XGA monitor Dual Monitor Document camera Multiple controllable cameras Tracker AudioScience microphone VCR Recording Video Cassette Recorder VCRVCR Playback Extra fixed cameras Telephone Add-On PC applications Additional microphones Tandberg Appendices Using Telesync TS-256 SW56/ISDN adapter Appendix 2 Connecting the system to the Switched 56 network Appendix 3 Environmental considerations Loudspeaker volumeIris control and lighting Background How to prepare a typical room for videoconferencing Guidelines for setting up videoconferencing rooms Appendix 4 Using the file system Custom logos · Go to the folder where your logo is located ABC Appendix 6 Security 111 112 Appendix 6 Declaration of Conformity Fecc Index Tandberg Videoconferencing System Index Current settings 93 outgoing video 30 Viewing a still image