Voice +V Commands Summary | Technics MT5634SMI-92, MT5634SMI-34

Chapter 6 – Voice Commands

Voice +V Commands Summary

These commands support Voice mode.

Command	Description
+VNH=	Automatic Hang Up Control
+FMI?	Report Manufacturer's ID
+FMM?	Report Product ID
+FMR?	Report Version Level
+FLO=	Select Flow Control Method
+VIP	Initialize Voice Parameters
+VRX	Enter Voice Receive State
+VTS	Produce DTMF and Tone Generation in Voice Mode
+VTS=?	Report Frequency Support
+VTX	Start Voice Transmission Process
+VGR=	Set the Gain for Received Voice Samples
+VGT=	Set the Volume for Transmitted Voice Samples
+VIT	Set DTE/DCE Inactivity Timer
+VLS=	Select Analog Source/Destination
+VLS=?	Identify Analog Source/Destination Configuration and Event Reporting Capabilities
+VRA=	Set Ring back Goes Away Timer
+VRN=	Set Ring back Never Appeared Timer
+VSD=	Set Silence Detection Sensitivity
+VSM=	Select Voice Compression Method
+VSM=?	Report Voice Compression Method
+VTD=	Select Default Beep Tone Duration Timer (DTMF/Tone Generation Duration)
+VDR=	Enable/Disable Distinctive Ring (Ring Cadence Reporting)
+VDT=	Control Tone Cadence Reporting
+VEM=	Event Reporting and Masking
+VEM=?	Report Event Reporting and Masking Capabilities
+VBT=	Set Modem Flow Control Assert and De-Assert Points
+VBT=?	Report Modem Flow Control Assert and De-Assert Points
+VPP=	Enable or Disable Voice Mode Packet Protocol
+VPR=	Select DTE/DCE Interface Rate (Turn Off Autobaud)

Voice +V Commands Detail

Command:	+FCLASS= <mode> <Enter>		Select Modem Operating Mode
Values:	0, 1, 2.0, 2, 3-7, 8, 9-15, 16-255
Default:	0
Result Codes:	OK if the command is accepted; ERROR if the parameter value is out of range.
Description:	The +FCLASS= command selects the mode of operation (data, facsimile, or voice), as shown
	below.
	+FCLASS= Modem Operating Mode
	0	selects data modem mode
	1	selects Service Class 1 (fax/data) modem mode
	2.0	selects Class 2.0 fax/data modem mode
	2	selects non-standard Class 2 modem
	3-7	reserved for other Fax modes
	8	selects IS-101 Voice mode
	9–15	reserved for other Voice modes
	16–255	reserved for future standards

SocketModem Global MT5634SMI Developer’s Guide

46

Image 46

Technics MT5634SMI-92, MT5634SMI-34 manual Voice +V Commands Summary, Voice +V Commands Detail, Command Description

Contents

MT5634SMI-34 MT5634SMI-92 Revisions Table of Contents Multi-Tech’s Flash Programming Protocol Appendix C Country Configuration and Result Codes Index Introduction Product Description SpecificationsProduct Description Features Matrix MT5634SMI Technical Specifications and Features TIA/EIA TR29.2 MT5634SMI-IT-92 Industrial Temperature 3.3V Build Option Standard Mechanical Specifications Physical Dimensions All Models Pin # Signal Name I/O Type Description Pin ConfigurationsDigital Ground Active High DCD status Tip Signal from TelcoRing Signal from Telco Active High RDX status INT Pin # Signal Description NameDgnd GND VCC PWR Electrical Characteristics Electrical Characteristics Timing Requirements for Parallel Write Handling PrecautionsTiming Requirements Timing Requirements for Parallel Read SocketModem Parallel Interface Internal Registers SocketModem Parallel Interface a Programmer’s DescriptionSocketModem Mimic MMM Operation Register Name Register Description Host Access Internal Registers Time Out InterruptsRegister Functional Descriptions Special Register Set Note *2 RBR Receive Buffer RX Fifo IER Interrupt EnableBit Priority Interrupt Source Interrupt Reset Control THR Transmit Holding Register TX Fifo LCR Line Control FCR Fifo ControlMCR Modem Control LSR Line Status MSR Modem Status DLM Divisor Latch MSByte SCR ScratchDLL Divisor Latch LSByte Baud Rate Clock Divisor Decimal DLM Value HEX DLL Value HEX AT Commands, S-Registers Result Codes AT Command Summary Modulation Handshake Set Register Value Dial string modifiers AT CommandsEnter Key DS= y Dial Stored Telephone Number Return Online to Data Mode Sr= n Set Register Value Sr? XON/XOFF Pacing Control \An Select Maximum MNP Block Size Zy=x Store Dialing Command\Bn Transmit Break \Kn Break Control \Nn Error Correction Mode Selection\Tn Inactivity Timer Data mode. The modem receives the break from the computer DCn AT Command Control \Xn XON/XOFF Pass-Through $EBn Asynchronous Word Length $RPn Ring Priority vs. AT Command Priority$Dn DTR Dialing $MBn Online BPS Speed #CBIn Local Callback Inactivity Timer #CBDn Callback DelayCallback Failed Attempts Reset #CBNy=x Store Callback Password Escape AT Commands Subparameters Commands+MS= Modulation Selection Modulation Possible rates bps1 Mod value Valid maxrate values bps +PCW=n Call Waiting Enable+PMH=n Modem on Hold Enable +PIG=n PCM Upstream Ignore +PMHF V.92 Modem Hook Flash +PMHT=n Modem on Hold Timer+PMHR=n Modem on Hold Initiate +PQC=n Quick Connect Control +VCID=n Caller ID Selection #Sx Enter Setup Password #S=x Store Setup Password Register Unit Range Default Description Registers S38 S48=7 S48=128 Result Codes Terse Verbose Description 111 Voice Commands Commands That Change for Voice Mode Support Voice CommandsVoice S-Register Summary Command Description Voice +V Commands SummaryVoice +V Commands Detail +FCLASS= mode Enter Select Modem Operating Mode AT+FCLASS=? Enter Display Service Class Capabilities Touch Tone Signals Digit Low frequency High frequency+FCLASS=8 Dtmf Detect Detect and Control Dtmf +FMM?Enter Report Product ID +VNH=hookEnter Automatic Hang-Up Control+FMI?Enter Report Manufacturers ID +FMR?Enter Report Version Level +VTS=string Produce Dtmf and Tone Generation in Voice Mode Enter Voice Receive State Start Voice Transmission Process +VTS=? Report Frequency SupportAT+VTS=? +VGR=gain Set the Gain for Received Voice Samples +VLS=label Select Analog Source/Destination +VGT=level Set the Volume for Transmitted Voice Samples+VIT=timer Set DTE/DCE Inactivity Timer Code Description +VRA=interval Set Ring Back Goes Away Timer +VSD=sds,sdi Set Silence Detection Sensitivity +VRN=interval Set Ring Back Never Appeared Timer+VSM=cml,vsr,scs,sel Select Voice Compression Method AT+VSM=? +VSM=? Report Voice Compression MethodIdentifier Description +VDT=enable,report Control Tone Cadence Reporting Enable Report DescriptionLsltcq +VEM=mask Event Reporting and Masking +VEM=? Report Event Reporting and Masking Capabilities +VBT=? Report Modem Flow Control Assert and Deassert Points Interface Configuration Commands+VPP=enable Enable or Disable Voice Mode Packet Protocol AT+VBT=? Flow Control Voice Mode Result Codes+VPR=rate Select DTE/DCE Interface Rate Turn Off Autobaud Valid Complex Event Report Tags Unsolicited Voice Mode Result CodesTag Description Voice Mode Shielded Codes Shielded Code Hex Event Report Description Ascii Sample Sessions Command ResponseSample Rate Selection and Suggested Compression Method DLE ETX AT+VLS=4AT+VTX AT+VLS=0 DLE NUL AT+VLS=2AT+VRX AT+VNH=1 Related Manuals DTE/DCE Interface RatesAdditional Information Fax Commands Basic Procedure Remote Configuration Country Code ConfigurationRemote Configuration Setup Using AT Commands Country Code ConfigurationUsing the Global Wizard Utility Country AT Command Result Code Hexadecimal Decimal Upgrade Overview Firmware Upgrade ProcedureUpgrade Steps Extract the Firmware Upgrade .Hex Files Download the Upgrade FileInstall the Flash Wizard Identify the Current Version of the Firmware Using the Flash Wizard Upgrade the Modem’s FirmwareRestore Your Parameters Modem Comments Multi-Tech Systems, Inc. Flash Programming ProtocolProgramming the Modem Handshake Sequence Other Programming Concerns Other Supported Boot Code CommandsATI4 Example Extended Address Record in Intel Format Intel Hex FormatData Record Char Pos Field Type Value Description End of File Record Char Pos Field Type Value Description Example End of File in Intel Format Appendix a Mechanical Details Serial Test/Demo Board Components Serial Test/Demo Board Block Diagram 5V / 3.3V Jumper JP1 Address/COM Port/ IRQ Select Jumpers JP2 and JP3 Parallel Test/Demo Board ComponentsOperating Voltage Select Jumper JP4 Parallel Test/Demo Board Block Diagram Figure A-4. Parallel Test/Demo Board Block Diagram Safety and EMC Approvals Telecom Approvals Regulatory Design Considerations Hardware Considerations Safety 5V Tolerant Inputs for 3.3V Modules FCC Part 15 Regulation Industry Canada FCC Part 68 Telecom Telecom Labeling Requirements From FCC Part 68 Subpart D Conditions for Registration Reregistration Fax Branding Statement Canadian Limitations Notice International Modem Restrictions EMC, Safety, and R&TTE Directive ComplianceIndustry Canada CS-03 Multiple Listing New Zealand Telecom Warning Notice South African Notice Appendix C Country Configuration Result Codes Country Country Config. hex ATI9 Response Appendix C Country Configuration and Result Codes Appendix C Country Configuration and Result Codes Appendix C Country Configuration and Result Codes Page Index Index Index Index