Appendix Material Safety Data Sheet | Teledyne 3160 specification

Appendix

A.4 Material Safety Data Sheet I

Section I – Product Identification

Product Name: Micro-Fuel Cells and Super Cells, all classes except A-2C, A-3, and A-5.

Electrochemical Oxygen Sensors, all classes except R-19. Mini-Micro-Fuel Cells, all classes.

Manufacturer: Teledyne Analytical Instruments

Address: 16830 Chestnut Street, City of Industry, CA 91749

Phone: (818) 961-9221

Customer Service: Extension 222

Environmental Health

and Safety: Extension 230

Date Prepared : 2/12/96

Section II – Hazardous Ingredients/Composition

Material or
Component	C.A.S. #	Quantity	OSHA PEL	ACGIH
TLV

Lead (Pb)	7439-92-1	3–20 gms	0.05 mg/m3	0.15 mg/m3
Potassium Hydroxide1310-58-3 1–5 ml		None 2 mg/m3
Solution 15% (KOH)

Section III – Physical/Chemical Characteristics

	Material	Boiling	Specific Vapor	Melting Density	Evap. Solubility		Odor
	Appearance	Boiling	Specific Vapor	Melting Density	Evap. Solubility		Odor
	or Compo-	Point (°C) Gravity Pres-		Point	Rate	in Water
	nent		sure	(°C)
		1744	11.34	na	na	Insoluble	Solid, silver
	Lead		na	328			gray, odorless
		1320	2.04	na	na	Complete	White or
	Potassium		na	360			slightly
	Hydroxide						yellow,
							no odor

A-4			TELEDYNE ANALYTICAL INSTRUMENTS

Image 62

Teledyne 3160 Appendix Material Safety Data Sheet, Customer Service Extension Environmental Health, Date Prepared 2/12/96

Contents

Model Copyright 1999 Teledyne Analytical Instruments Iii Table of Contents Maintenance & Troubleshooting Appendix Teledyne Analytical Instruments Variable Features FeaturesFixed Features Introduction Introduction 3160DA Dual fuel cell Introduction ComponentsOptions and Model Numbers Introduction Applications Operational Theory Principles of Operation Major Components Operational Theory Micro-Fuel Cell Sensor Sample System Operational Theory Electronics and Signal Processing Model 3160 flow schematic Operational Theory Analog signal output offset Identifier Range Scale Voltage CurrentmA Defaults Programmable Options Front Panel InstallationUnpacking the Analyzer Qty Description Rear Panel Analyzer front and rear panels Instrument Air Compressed Air Fitting Installation Gas Line ConnectionsSpan Gas Sample Gas Sensor Installation Electrical Connections Voltage Selection 3160 Rear Panel Fuse Changing Removing the Voltage Card Fuse Replacement Installation Checklist 3 RS-232 Serial Digital Port Operations Front Panel Controls Cell Output Factor Span Factor Modes of OperationSpinning Wheel Operations Changing Passwords For Remote Monitoring and Control Uled Span in Progress Operations Cold Start-Up Operations Calibration Zeroing Operations Operations Calibration Using Span Gas Operations Operations Operations Select Active Sensor Two Cells Only Setup Operations Operations O2 Range Set-Up Accpt Operations Set-Up Alarms Cold Start Operations Operations Logger Set-Up Operations Operations Set-Up Clock Functions Accpt Teledyne Analytical Instruments Operations Operations System Statistics Comm. Std. for 1200B Bell USA/CCITT Baud rateAscii Data Bits 7 or Stop Bits 1 or Operations Operations Sensor Maintenance Maintenance & TroubleshootingRoutine Maintenance Scrubber Maintenance Troubleshooting Symptom Cause Correction Maintenance & Troubleshooting Symptom Cause Correction Maintenance & Troubleshooting Appendix SpecificationsOperating Temperature0-50C 32 -122 F Altitude 1,609 m Relative Humidy Up to 99% Teledyne Analytical Instruments Appendix Recommended Spare Parts List Drawing List Date Prepared 2/12/96 Appendix Material Safety Data SheetCustomer Service Extension Environmental Health Material or Component S. # Quantity Section IV Fire and Explosion Hazard Data Protective measures during cell replacement Exposure Section Viii Control Measures Address Product NameManufacturer Phone Exposure limits Osha PEL Signs/symptoms of exposurePrimary route of entry Effects of overexposure Ingestion Protective measures Disposal