Teledyne Trace Oxygen Analyzer, 3000TA-XL-EU specs

Appendix		Model 3000TA-XL-EU

A7 - Installling and Replacing a new Insta-Trace

Micro-fuel Cell

Read completely before beginning the procedure

Cell Block

Lift up Gate to removed Cell Holder.

Micro fuel cell

Protective Film/ Seal Cover (Located this side)

O-Ring

It is important to minimize the amount of time a Teledyne Trace Oxygen sensor is exposed to air during the installation process. The quicker the sensor can be installed into the unit, the faster your sensor will recover to low oxygen measurement levels.

CAUTION: Do not touch the sensing surface of the cell. It is covered with a delicate Teflon membrane that can leak when punctured. The sensor must be replaced if the membrane is damaged.

Check O-ring in the base of the cell holder before installing a new cell. Replace it if worn or damaged.

Cell Holder

A-12	Teledyne Analytical Instruments

Image 78

Teledyne Trace Oxygen Analyzer, 3000TA-XL-EU operating instructions Read completely before beginning the procedure

Contents

Trace Oxygen Analyzer Teledyne Analytical Instruments Model 3000TA-XL-EU Copyright 1999 Teledyne Analytical Instruments Iii Trace Oxygen Analyzer Specific Model Information Ground Protective Earth Teledyne Analytical Instruments Operational Theory Trace Oxygen Analyzer Table of Contents IntroductionInstallation Operation Maintenance Appendix Vii Trace Oxygen Analyzer Appendix Combustible GAS Usage Warning Viii Typical Applications Main Features of the AnalyzerOverview Trace Oxygen Analyzer Introduction Model Designations Introduction Model 3000TA-XL-EU Front Panel Operator Interface Model 3000TA-XL Front Panel Introduction Model 3000TA-XL-EU Rear Panel Equipment Interface Analog Outputs RS-232 Port Remote ProbeNetwork I/O Trace Oxygen Analyzer Operational Theory Operational Theory IntroductionMicro-Fuel Cell Sensor Principles of Operation Operational Theory Model 3000TA-XL-EU Anatomy of a Micro-Fuel Cell Electrochemical Reactions + 2H 2O + 4e → 4OH Calibration Characteristics Effect of Pressure Characteristic Input/Output Curve for a Micro-Fuel Cell Sample System TOP Flow Diagram-Sample Under Pressure Standard Model Electronics and Signal Processing Electronic Component Location Inside the Model 3000TA-XL Block Diagram of the Model 3000TA-XL Electronics Operational Theory Model 3000TA-XL-EU Trace Oxygen Analyzer Installation Unpacking the AnalyzerMounting the Analyzer Installation Model 3000TA-XL-EU Rear Panel Connections Gas Connections Rear Panel of the Model 3000TA-XL PrimaryInputPower 2.2 50-Pin Equipment Interface ConnectorElectrical Connections Equipment Interface Connector Pin Arrangement Pin Function Pin Contact Remote Calibration Connections Range ID Relay Connections 2.3 RS-232 Port FET Series Resistance Command Description Parameter Setting Installing the Micro-Fuel Cell Testing the System Removing the Micro-Fuel Cell Trace Oxygen Analyzer Operation Auto Ranging on Using the Data Entry and Function Buttons Operation Model 3000TA-XL-EU System Function Analyze System Operation Model 3000TA-XL-EU Setting up an Auto-Cal Password Protection Entering the Password Installing or Changing the Password System Self-Diagnostic Test Logout Version Screen Air Calibration Calibration of the AnalyzerSpan Gas Calibration Zero Cal Auto Mode Zeroing Manual Mode Zeroing Cell Failure Auto Mode Spanning Operation Model 3000TA-XL-EU Span Cal Manual Mode Spanning Switching of Sample Streams Span Failure Alarms Function Special Notes on Hydrogen Gas Stream AL-1 AL-2 Choose Alarm Range Function Setting the Analog Output Ranges Fixed Range Analysis Signal Output Analyze Function Range Voltage Current mA MED Trace Oxygen Analyzer Maintenance Routine MaintenanceCell Replacement Storing and Handling Replacement Cells Maintenance Model 3000TA-XL-EU When to Replace a Cell Removing the Micro-Fuel Cell Removing the Micro-Fuel Cell Warranty Fuse Replacement Removing Fuse Block from Housing System Self Diagnostic Test Maintenance Model 3000TA-XL-EUMajor Internal Components Cleaning Rear-Panel Screws Troubleshooting Solution Specifications Operating Temperature 5-35 C Appendix Recommended 2-Year Spare Parts List Drawing List 19-inch Relay Rack Panel Mount 3000XL Series Analyzers Conversions Page Material Safety Data Sheet Section IV Fire and Explosion Hazard Data Protective measures during cell replacement Exposure Section Viii Control Measures Read completely before beginning the procedure