Electrical Specifications | Texas Instruments 3138 155 232931

CC2420

6 Electrical Specifications

Measured on CC2420 EM with transmission line balun, TA = 25 °C, DVDD3.3 and VREG_IN = 3.3 V, internal voltage regulator used if nothing else stated.

6.1	Overall

Parameter		Min.	Typ.	Max.	Unit	Condition / Note
RF Frequency Range		2400		2483.5	MHz	Programmable in 1 MHz steps, 5
						MHz steps for compliance with [1]

6.2	Transmit Section

Parameter		Min.	Typ.	Max.	Unit	Condition / Note
Transmit bit rate		250		250	kbps	As defined by [1]

Transmit chip rate		2000		2000	kChips/s	As defined by [1]

Nominal output power		-3	0		dBm	Delivered to a single ended 50 Ω
						load through a balun.
						[1] requires minimum –3 dBm

Programmable output power range			24		dB	The output power is
						programmable in 8 steps from
						approximately –24 to 0 dBm.

Harmonics
2nd harmonic			-44		dBm	Measured conducted with 1 MHz
3rd harmonic			-64		dBm	resolution bandwidth on spectrum
3rd harmonic			-64		dBm	analyser. At max output power
						analyser. At max output power
						delivered to a single ended 50 Ω
						load through a balun. See page
						54.

Spurious emission						Maximum output power.
30 - 1000 MHz			-56		dBm	Complies with EN 300 328, EN
1– 12.75 GHz			-44		dBm	300 440, FCC CFR47 Part 15
1.8 – 1.9 GHz			-56		dBm	and ARIB STD-T-66
5.15 – 5.3 GHz			-51		dBm

Error Vector Magnitude (EVM)			11		%	Measured as defined by [1]
						[1] requires max. 35 %

Optimum load impedance			95		Ω	Differential impedance as seen
			+ j187			from the RF-port (RF_P and
						RF_N) towards the antenna. For
						matching details see the Input /
						Output Matching section on page
						54.

			SWRS041B			Page 9 of 89

Image 9

Texas Instruments 3138 155 232931 manual Electrical Specifications, Overall, Transmit Section

Contents

Key Features ApplicationsProduct Description Table of contents RF Data Buffering Ordering Information General Information ITU-T Abbreviations References Features Operating Conditions Absolute Maximum RatingsParameter Min Max Units Condition Parameter Min Typ Max Units Condition Overall Electrical SpecificationsTransmit Section Parameter Min Typ Max Unit Condition / Note Receive Section Rssi / Carrier Sense If SectionFrequency Synthesizer Section VDD Digital Inputs/Outputs Battery Monitor Power SupplyVoltage Regulator CC2420 Pin Pin Name Pin type Pin Description Pin Assignment Avddadc Circuit Description CC2420 simplified block diagram CC2420 Application Circuit Power supply decoupling and filteringInput / output matching Bias resistor Description Overview of external components Transceiver Transceiver Bill of materials for the application circuits Ieee 802.15.4 Modulation Format Symbol Chip sequence C0, C1, C2, … , C31 Phase Configuration Overview SmartRF Studio user interface Evaluation Software 13 4-wire Serial Configuration and Data Interface Pin configurationRegister access Parameter Symbol Min Max Units Conditions SPI timing specification Status byte RAM access Configuration registers write and read operations via SPI CC2420 RAM Memory Space Fifo access Multiple SPI accessAddress Byte Ordering Name Description Microcontroller Interface and Pin Description Configuration interface Rxfifo overflow Receive mode Pin activity examples during receive Demodulator, Symbol Synchroniser and Data Decision Frame Format Demodulator Simplified Block Diagram MAC protocol data unit Transmitted Synchronisation Header Length field Format of the Frame Control Field FCF Frame check sequence Buffered transmit mode Buffered receive modeRF Data Buffering Fifop Unbuffered, serial mode Acknowledge Frames Address Recognition Acknowledge frame format Radio control state machine Radio control states Keys MAC Security Operations Encryption and AuthenticationNonce / counter Ieee 802.15.4 Nonce In-line security operations CC2420 Security Flag Byte Stand-alone encryption CTR mode encryption / decryption CBC-MAC21.7 CCM Mode LMIC Time Linear if and AGC SettingsRssi / Energy Detection Timing Link Quality Indication ValueRF Level dBm Frequency and Channel Programming Clear Channel Assessment VCO and PLL Self-Calibration Output Power ProgrammingVoltage Regulator 27.1 VCO Voltage regulator, simplified schematic Battery Monitor Crystal Oscillator Transmitter Test Modes Input / Output MatchingCrystal oscillator component values Unmodulated carrier CC2420 Modulated spectrum plot System Considerations and Guidelines Battery operated systems Low-cost systemsBER / PER measurements Antenna Considerations PCB Layout Recommendations CC2420 Address Register Register type Description Configuration Registers Saes Configuration registers overview Bit Field Name Reset Main 0x10 Main Control RegisterXOSC16MBYPASS MDMCTRL0 0x11 Modem Control Register Reservedframemode Pancoordinator AdrdecodeCCAHYST20 CCAMODE10 Autocrc Autoack Preamblelength Rssi 0x13 Rssi and CCA Status and Control Register MDMCTRL1 0x12- Modem Control RegisterCORRTHR40 Demodavgmode Modulationmode RSSIVAL70 Txctrl 0x15 Transmit Control Register Syncword 0x14 Sync Word RXMIXBUFCUR10 RXCTRL0 0x16 Receive control register RXCTRL1 0x17 Receive control register Caldone Calrunning Locklength Lockstatus Fsctrl 0x18 Frequency Synthesizer Control and Status SECMODE10 SECCTRL0 0x19 Security Control Register SECCTRL1 0x1A Security Control Register Battmon 0x1B Battery Monitor Control registerSectxl Secrxl Battmonok Battmonen Battmonvoltage IOCFG1 0x1D I/O Configuration Register IOCFG0 0x1C I/O Configuration RegisterManfidl 0x1E Manufacturer ID, Lower 16 Bit HSSDSRC20 SFDMUX40 CCAMUX40 Fsmtc 0x20 Finite state machine time constants Manfidh 0x1F Manufacturer ID, Upper 16 Bit Isused = is * Isandmask + Isormask Manand 0x21 Manual signal and override register1 Agcctrl 0x23 AGC Control Manor 0x22 Manual signal or override registerVgagainoe Lnamixgainmodeo AGCTST0 0x24 AGC Test Register AGCTST1 0x25 AGC Test RegisterAGCTST2 0x26 AGC Test Register FSTST0 0x27 Frequency Synthesizer Test Register FSTST1 0x28 Frequency Synthesizer Test RegisterFSTST2 0x29 Frequency Synthesizer Test Register FSTST3 0x2A Frequency Synthesizer Test Register Rxbpftst 0x2B Receiver Bandpass Filters Test RegisterFsmstate 0x2C Finite state machine information Adcclockdisable Adctst 0x2D ADC Test RegisterDactst 0x2E DAC Test Register Toptst 0x2F Top Level Test Register Oscillator must be running for accessing the RxfifoTxfifo 0x3E Transmit Fifo Byte register Rxfifo 0x3F Receive Fifo Byte register Test Output Signals CCA test signal select tableSignal output on CCA pin Description Signal output on SFD pin Description SFD test signal select table Quad Leadless Package QLP Package Description QLP Package thermal properties Recommended layout for package QLPSoldering information Thermal resistance 40.4 Carrier tape and reel specification 40.3 Plastic tube specificationTube Specification Tape and Reel Specification General Information 42.1 Document HistoryRevision Date Description/Changes Product Status Definitions Data Sheet Identification Product Status Definition Address Information TI Worldwide Technical Support InternetProduct Information Centers 2007, Texas Instruments. All rights reserved Important Notice