APPENDIX 1 SPECIFICATIONS | ENGLISH VERSION |
| A1.3 Media |
|
|
A1.3.1 | Media Type (Cont.) |
|
|
| [Unit: mm] | |||
|
|
| Label dispensing mode | Batch mode | Strip mode | Cut mode |
| |
| Item |
|
|
| Rotary cutter | Swing cutter | ||
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| c |
|
| Label | 10.0 – 1500.0 | 25.4 – 1500.0 | 38.0 - 1500.0 | 38.0 – 1500.0 |
| Media pitch |
|
|
|
|
|
| |
|
| Tag | 10.0 – 1500.0 | 3”/sec., 5”/sec.: 30.0 – 1500.0 | 25.4 – 1500.0 | |||
| d |
|
| 8”/sec.: 38.0 – 1500.0 | ||||
|
|
|
|
|
|
|
| |
| eLabel length |
|
| 8.0 – 1498.0 | 23.4 – 1498.0 | 25.0 – 1494.0 | 25.0 – 1494.0 (*1) | |
| fWidth including backing paper | 30.0 – 140.0 | 50.0 – 140.0 | 30.0 – 112.0 | 30.0 – 140.0 | |||
| (See NOTE 5.) |
|
|
|
| |||
| gLabel width | (See NOTE 5.) | 27.0 – 137.0 | 47.0 – 137.0 | 27.0 – 109.0 | 27.0 – 137.0 | ||
| hGap length |
|
| 2.0 – 20.0 | 6.0 – 20.0 |
| ||
| iBlack mark length (Tag paper) |
|
| 2.0 – 10.0 |
| |||
| Effective print width |
|
| 10.0 – 128.0 |
| |||
| j |
|
| Label | 6.0 – 1496.0 | 21.4 – 1496.0 | 23.0 - 1492.0 | 23.0 – 1492.0 |
| Effective print length | Tag | 8.0 – 1498.0 | 3”/sec., 5”/sec.: 28.0 – 1496.0 | 23.0 – 1496.0 | |||
| k |
|
| 8”/sec.: 36.0 – 1496.0 | ||||
|
|
|
|
|
|
|
| |
| Print speed up/slow down area |
|
| 1.0 |
| |||
| Thickness |
|
| Label |
|
| 0.13 – 0.17 |
|
|
|
| Tag |
|
| 0.15 – 0.29 |
| |
|
|
|
|
|
|
| ||
| Maximum effective length for on the fly issue |
|
| 749.0 |
| |||
| Maximum outer roll diameter |
|
| Ø 200 |
| |||
| Roll direction |
|
|
|
| Inside |
| |
| Inner core diameter |
|
| Ø 76.2±0.3 |
| |||
NOTES:
1.To ensure print quality and print head life use only TOSHIBA TEC specified media.
2.The media length specifications for use of the cutter are:
*1: When issuing a label using the swing cutter, label length should be 35.0 mm – (Gap length/2).
3.When marking black marks on the label rolls, they should be marked at the gaps.
4.“On the fly issue” means that the printer can feed and print without stopping between labels.
5.There are restrictions in use of the media which is narrower than 50 mm. For details, refer to TOSHIBA TEC service representative.
A1.3.2 Detection Area of the Transmissive Sensor
The Transmissive Sensor is movable from the centre to the left edge of media.
The Transmissive Sensor detects a gap between labels, as illustrated below.
<Label> |
|
|
|
|
|
|
|
|
|
|
|
|
| Centre of media | |||||
Sensor position |
|
| Area to be detected. |
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Print side |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Min. 2.0 mm |
|
|
|
|
|
|
|
|
|
| Label |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| Gap |
|
|
|
|
|
|
| |
(Min. 6.0 mm when using |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
the | cutter module.) |
|
|
|
|
|
|
|
|
| Label |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Min. 12 mm
Media feed direction
Sensor is movable within this range.
EA1- 3
