Manuals / Toshiba / Computer Equipment / Printer

Toshiba BSX5TTS25QMR, BSX5TTS22QMR, B-SX5T SERIES owner manual EA1-1, EA2-1, EA3-1, EA4-1

Models: BSX5TTS25QMR BSX5TTS22QMR B-SX5T SERIES

1 56

Download 56 pages 47.42 Kb

Page 6

ENGLISH VERSION EO1-33036

APPENDIX 1 SPECIFICATIONS		EA1-1
A1.1	Printer	EA1-1
A1.2	Options	EA1-2
A1.3	Media	EA1-2
	A1.3.1 Media Type	EA1-2
	A1.3.2 Detection Area of the Transmissive Sensor	EA1-3
	A1.3.3 Detection Area of the Reflective Sensor	EA1-4
	A1.3.4 Effective Print Area	EA1-4
A1.4	Ribbon	EA1-5
APPENDIX 2 MESSAGES AND LEDS		EA2-1
APPENDIX 3 INTERFACE		EA3-1
APPENDIX 4 PRINT SAMPLES		EA4-1
GLOSSARIES
INDEX

WARNING!

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

CAUTION!

1.This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC.

2.The contents of this manual may be changed without notification.

3.Please refer to your local Authorised Service representative with regard to any queries you may have in this manual.

Image 6

Toshiba BSX5TTS25QMR, BSX5TTS22QMR, B-SX5T SERIES owner manual EA1-1, EA2-1, EA3-1, EA4-1

Contents

SX5T Series CE Compliance for EU only Vorsicht Wkhsoxj Precautions Request Regarding Maintenance Table of Contents EA3-1 EA1-1EA2-1 EA4-1 Introduction Features Product OverviewUnpacking Accessories Front View DimensionsAppearance Rear View Operation Panel Interior Printer Setup Precautions Procedure before Operation Connecting the Cables to Your Printer Gori Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Loading the Media Parts, be sure to load Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Batch mode Strip modeSTANDARD/PEEL OFF position Build-in rewinder mode Adjustment Cut mode Loading the Ribbon Auto Ribbon Saving Mode Pcmcia Cards 3517 Test Print $5&2 Printer’s power OFF then back to on and check that the LCD Sample of the bar code test print label On Line Mode Operation Panel Reset Operation Dump Mode Maintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Care/Handling of the Media and Ribbon Optional Cutter Module Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart key Possible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Removing Jammed Media Do not use any tool that may damage the Print Head Threshold Setting Threshold setting procedure Appendix 1 Specifications A1.1 PrinterModel A1.3.1 Media Type A1.2 OptionsA1.3 Media Label A1.3.2 Detection Area of the Transmissive Sensor Label A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaTag paper with square holes A1.4 Ribbon Figure below shows the effective print area on the media Symbols in the message Appendix 2 Messages and Leds 67$9$ Appendix 3 Interface „Interface Cables Appendix 4 Print Samples EAN13+2 digits Interleaved 2 CODE39 StandardJAN13, EAN13 EAN13+5 digits UPC-A+5 digits Industrial 2 Glossaries Bar code Print head element USB Universal Serial Bus Index Index Page Page EO1-33036B