APPENDIX 2 MESSAGES AND LEDS | ENGLISH VERSION |
APPENDIX 2 MESSAGES AND LEDS
APPENDIX 2 MESSAGES AND LEDS
Appendix 2 describes the LCD messages displayed on the operation panel.
Symbols in the message
1:Å: The LED is illuminated. ~: The LED is flashing. z: The LED is unlit.
2:****: the number of unprinted media. Up to 9999 (in pieces)
3:%%%%%%%: ATA Card’s remaining memory 0 to 9999999 (in K bytes)
4:###: Flash memory card remaining memory for PC save area: 0 to 895 (in K bytes)
5:&&&&: Remaining flash memory capacity for storing writable characters 0 to 3147 (in K bytes)
|
| LED Indication |
| Restoration by Acceptance of | ||
|
|
|
|
| Status Request | |
No. | LCD Message | Printer Status | RESTART key | |||
Reset Command | ||||||
|
| POWER ONLINE ERROR |
| Yes/No | ||
|
|
| Yes/No | |||
|
|
|
| |||
|
|
|
|
| ||
1 | ON LINE |
|
| Å |
| In online mode |
| Yes | |
ON LINE |
|
| ~ |
| In online mode (The printer in | Yes | |||
|
|
|
|
|
| communication) |
|
|
|
2 | HEAD OPEN |
|
|
|
| The print head block is opened in online | Yes | ||
|
|
|
| mode. |
|
|
| ||
|
|
|
|
|
|
|
|
| |
3 | PAUSE **** |
|
|
| z | The printer is paused. |
| Yes | Yes |
|
|
|
|
|
| A parity, overrun, or framing error has | Yes | Yes | |
4 | COMMS ERROR |
|
| occurred during communication through |
|
| |||
|
|
|
|
|
| the |
|
|
|
5 | PAPER JAM | **** |
|
| The media is jammed during paper feed. | Yes | Yes | ||
6 | CUTTER ERROR**** |
|
| A problem has occurred with the cutter | Yes | Yes | |||
|
| module. |
|
|
| ||||
|
|
|
|
|
|
|
|
| |
7 | NO PAPER | **** |
|
| The media has run out, or the media is | Yes | Yes | ||
|
| not loaded properly. |
|
|
| ||||
|
|
|
|
|
|
|
|
| |
8 | NO RIBBON | **** |
|
| The ribbon has run out. |
| Yes | Yes | |
9 | HEAD OPEN | **** |
|
| Feed or printing was attempted with the | Yes | Yes | ||
|
| print head block open. |
|
|
| ||||
|
|
|
|
|
|
|
|
| |
10 | HEAD ERROR |
|
|
| There is a problem with the print head. | Yes | Yes | ||
11 | EXCESS HEAD TEMP |
|
| The print head is overheated. | No | Yes | |||
|
|
|
|
|
| The ribbon has been torn. | A problem | Yes | Yes |
12 | RIBBON ERROR**** |
|
| has occurred with the | sensor that |
|
| ||
|
| determines the torque for the ribbon |
|
| |||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| motor. |
|
|
|
13 | REWIND FULL | **** | z | Å | rewinderAn overflowunit. error has occurred in the | Yes | Yes | ||
| SAVING%%%%%%% |
|
| In writable character or PC command | Yes | ||||
14 | or |
|
| Å | z | save mode |
|
|
|
| SAVING ###&&&& |
|
|
|
|
|
| ||
15 | FLASH WRITE ERR. |
|
| An error has occurred while writing to | No | Yes | |||
|
| flash memory or ATA card. |
|
|
| ||||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| An erase error has occurred in | No | Yes | |
16 | FORMAT ERROR |
|
| formatting the flash memory or ATA |
|
| |||
|
|
|
|
|
| card. |
|
|
|
17 | FLASH CARD FULL |
|
| Data cannot be stored because the flash | No | Yes | |||
|
| memory or ATA card is full. |
|
| |||||
|
|
|
|
|
|
|
| ||
18 | Display of error |
|
|
| A command error has occurred in | Yes | Yes | ||
| message (See Notes.) |
|
| analyzing the command. |
|
|
| ||
19 | POWER FAILURE |
| ÅA power failure has occurred. | No | No | ||||
20 | INTIALIZING… |
|
|
| A flash memory card is being initialised. | ||||
21 | 100BASE LAN | Å | z | z | 100 Base LAN Board is being | ||||
| INITIALIZING… |
|
|
| initialized. |
|
|
| |
EA2- 1
