Names of the Main Components | Toshiba e-studio 550/650/810 specs

1. FINISHING MODES AND FINISHERS (OPTIONAL)

There are 2 types of optional finishers (MJ-1017 and MJ-1018). Functions available differ depending on whether a finisher is installed and which type of finisher it is.

- Press the key on the basic screen on the right (shaded), and confirm the finishing modes on the panel.

*The touch panel used in this chapter appears when the optional saddle stitch finisher (MJ-1018, with hole punch unit) and inserter are installed with your copier.

Names of the Main Components

Upper cover

Inserter

Trays

(sold separately)

6	Hole punch unit
	Hole punch unit
	(sold separately)

Front cover

Lower cover

Saddle stitch tray (MJ-1018 only)

When the finisher trays reach their maximum loading capacity ( Page 9-4), the following message appears:

Remove paper from the finisher

Remove the copies from the trays and the copier automatically resumes making copies.

6-2	SELECTING FINISHING MODES

Image 123

Toshiba e-studio 550/650/810 manual Finishing Modes and Finishers Optional, Names of the Main Components

Contents

Page Page Sleep Mode Default Time STUDIO550/650/810 Copier model Base model Off ModeOff Mode Default Time Automatic Energy Save Default Time Supplies / Parts Toshiba Quality is Second to None Toshiba Quality is Second to None TonerGeneral Preface Preface Features of the e-STUDIO550/650/810 Table of Contents Table of Contents Maintenance When the graphic symbols flash on the touch panel Disclaimer Notice Installation Precautions Handle and use the copier gently and carefully PrecautionsGeneral Precautions Be sure to disconnect the power-cord plug Explanatory Label Fixing the adjusters stoppers Before Making Copies Main Components Optional Equipment Optional Equipment Configuration Control Panel Start key Timer lampFunction Clear key Stop key Touch Panel Message DisplayTouch-keys Clearing the Functions Selected Settings set functions confirmation key Turning on the Power Switch Turning on the Power Switch/Auto Job StartTurning on the Power Switch Turn on the power switch After Copying is Finished Controlling the Use of the Copier with Department Codes Turning on the Power Switch HOW to Make Copies General Copying Procedures Place the originalsPlace the next original 2nd side and press Start key Exiting Copy Papers When Coming Across the Situations below Feeder Paper Type Paper Size Remarks Acceptable Copy Paper Types and Sizes Pay attention to the following points Handling and Storing Paper Changing the Paper Size of the Drawer Setting Copy Paper Press the JOB Status key on the control panel Setting the Drawer for Special Uses If you want to select the Cover , Insert , or TAB Paper Acceptable Original Types and Sizes Setting Originals When Placing an Original on the Glass Setting Originals Exiting Originals When Using the Reversing Automatic Document Feeder Originals Continuous Feed ModeAfter aligning the edges of originals well, place Them face up and align the slides to the width Confirming auto job start Auto JOB Start JOB PresetConfirming and Cancelling Auto Job Start Press the Start key Interrupt Copying Press the Interrupt keyReplace the original with a new one. Stopping the Copy Operation Deleting the Job Deleting or Changing Order of Pending Jobs Changing order is completed 18HOW to Make Copies Setting of Basic Copy Modes Automatic Paper Selection APS Paper Selection Manual Paper Selection Reduction and Enlargement Copying Press the AMS keyPlace the originals. Press the Original Size key of the same size as the original Reduction and Enlargement Copying DUPLEXCOPYING1-SIDED,2-SIDED,BOOK-TYPE Follow the same procedure 1 to 3 as shown above Duplex Copying 1-SIDED, 2-SIDED, BOOK-TYPEBook-Type Originals 2-Sided Copies Select A4 or B5 copy size Press the Book 2 key Select the book copying type 10SETTING of Basic Copy Modes Copy Density Adjustment Copy Density Adjustment Manual Copy Density ModePress Auto on the basic screen Selecting Original Mode Quick Access Menu Using the Editing Functions Image Shift Providing Right or Left MarginPage2-4 Press the Start key Providing a Bookbinding Margin Edge Erase Place in the drawers DUAL-PAGE Scanned Turn to the next page, set the book again and press Press the lower SET key Y Zoom Trimming/Masking Image Editing Area Enter the distance values read in for the specified area Mirror Image Image Editing Negative/Positive Reversal 4IN1 2IN1 Press Start key Select the type of the original Copying with Annotation Numbering Copying Place paper in the drawers Select the paper type Magazine Sort from the Editing Menu To have copies stapled, press the Staple on Key Cover Copying Select the desired cover sheet key Sheet Insertion Copying Select the number of copies or sets Into the slit hole of A4-TAB or LT-TAB TAB Paper ModeSetting Tab Paper in the Drawer Pull the second drawer out Tab Width Adjustment Key, then adjust the tab extension tab width TAB Paper MODEContShift width then press the SET key Tab Paper Copying Press the Copy on TAB key Press the SET keyPlace tab paper in the drawer or the bypass guide Tab Paper Insertion Place tab paper in the drawer or the bypass guidePress the Blank TAB Insert key Press the Copied TAB Insert key Tab Paper Insertion and Copying Document Storage Press Start key Overlay Stored image starts printing out Press the Start key Confirming Overlay Test Print Overlay Sharpness Adjustment Press the Start key Cancelling the Sharpness AdjustmentPress Soft or Sharp key Direction of Duplex Copy Images Rotation Using the Special Functions Continuous Original Feeding / Single Original Feeding Place an original MIXED-SIZED Originals JOB Memory Key to enter the programme JOB Memory Confirming Stored Copy Modes Slides with the size of the paper Bypass CopyingBypass copying Set sheets of paper on the bypass guide and align Press the Start key Set the Other size key as necessary Bypass COPYINGcontBypass Copying on Standard Size Paper Perform steps 1 to 2 on pages 5-8 Bypass Copying on Non-Standard Size Paper Key in each dimension, then press the Memory key Bypass Copying on Non-Standard Size PapercontStoring a Non-Standard Size in the Memory Set the ON/OFF times for each day of the week Weekly Timer Setting has been completed Setting the Other Size KEY Setting the Date and Time Check that the settings are all correctSetting the Clock for Daylight Saving Time Clearing the Automatic Energy Saving Mode Setting the Automatic Energy Save Mode Clearing the Off-Mode/Sleep Mode Setting the Automatic OFF-MODE Press the key of the desired language Switching Languages Department Codes Department Codes Input the master code name, and press the SET keyMaster code name is displayed in the department number Registration / Change / Deletion of Department Code 22USING the Special Functions Page 24USING the Special Functions Deleting of the selected department code is completed Counter reset is completed Print out department code Entering Letters Entering Letters Example Correct Meeting to Meeting Entering Letters Selecting Finishing Modes Names of the Main Components Finishing Modes and Finishers Optional Press the Sort or Group key SORT/GROUP Copying Staple Sorting Optional Maximum Number of Sheets that can be Stapled Magazine Sort & Saddle Stitch Mode Booklet Mode LT-R Available Conditions for Saddle Stitch Number of punch holes and available paper sizes Hole Punch Mode Optional Paper Acceptable to Set in the Inserter Inserter Mode Optional Inserter Mode OPTIONALCont Setting the InserterPress the Size key Press the Start key Sheet Insertion Set with the control panel of the inserter Using only Staple and Hole Punch 14SELECTING Finishing Modes When the Graphic Symbols Flash on the Touch Panel Description of the Flashing Graphic Symbols Place the paper in the drawer ADD Paper SymbolAdding Paper to the Drawers Pull the drawer out carefully until it comes to a stop Tray B ADD Paper SymbolAdding Paper to the Tandem LCF Large Capacity Feeder Pull the tandem LCF out carefully until it comes to a stop Close the cover of the external LCF Place the paper on the elevator tray Open the front cover Replace Toner Cartridge Symbol Return used toner cartridges to your service technician Replace Toner Bag Replace Toner Cartridge SymbolAdditional Explanation Dispose of Used Toner Separating it from the copier Clear Paper SymbolConnecting with the copier Moving the finisher optional Clear Paper Symbol Lift the blue handle second as shown on the right Remove any misfed paper Open the bypass cover Paper Misfeed inside of the Copier Open the paper feed cover Open the exit cover Remove any misfed paperTurn the handle in the direction of the arrow 11Remove any misfed paper Pull the transfer unit out until it comes to a stopLift the grip, then turn the knob in the direction Arrow to remove any misfed paperPage Open the cover while lifting the grip Return the external LCF to its original positionPaper Misfeed in the Inserter optional Pull the inserter optional away from the copier Pull down the grip Remove any misfed paper 18WHEN the Graphic Symbols Flash on the Touch Panel Only when the saddle stitch finisher MJ-1018 is installed Turn it clockwise Counter clockwise.ThenPush the left-hand knob Adding Staples Optional Adding Staples Optional Close the front cover of the finisherSaddle Stitch Unit Firmly and that A3, A4-R, B4 size paper is set Copier Removing Jammed Staples Optional Close the front cover of the finisher Saddle Stitch Unit Return the staple case to its original position Removing Jammed Staples Optional Disposing of Accumulated Punched Paper Bits Optional Call Service Symbol / Periodic Maintenance Message Maintenance Items for Daily Check Weekly MaintenancePower switch ON/OFF status Daily Inspection Copy density is too low Simple TroubleshootingDisplay does not change when keys or icons are pressed Copier does not start Copy images are blurred Simple TroubleshootingCopy density is too high Copies are stained Specifications & Options STUDIO550/650/810 Specifications B4, Folio Continuous Copying Speed Specificatons of Options FinishersTray Loading Capacity LD,LG,LT-R,COMP Packing List Numbers Index Finisher Index Paper Misfeed in the Inserter When Using the Reversing Automatic Document To Service Technicians Periodic Maintenance Kanda NISHIKI-CHO, CHIYODA-KU, TOKYO, 101-8442, Japan