Line Lock Phase | Toshiba IK-WR01A specification

■LINE LOCK PHASE

When a video switcher switches two or more cameras, the picture may fluctuate on the video monitor due to the different AC line phase of each camera. In this case, adjust the V PHASE controller to get a stable image.

Line Lock V PHASE CONTROL

NOTE

●The camera is synchronized to the power frequency of 60±1 Hz covering a normal fluctuation of the power frequency. However, the camera may not cover a large fluctuation caused from the power generated by an engine generator, etc.

●It takes about 10 seconds or more until a stable synchronization is obtained after the power is turned on. This is normal, because several seconds are required to stabilize the camera against power noise.

Installation/Set up

and OperationViewing

Recording

Setting up

Others

17

Image 17

Toshiba IK-WR01A operation manual Line Lock Phase

Contents

Model IK-WR01A Important Safety Instructions Introduction Viewing and Operation Introduction Mode Setting Switch Lens Iris ADJ Names and Features of PartsLine Lock Phase ADJ Monitor Out Connector Ethernet Port Video Out Jack Installation/Setup Adjust the Angle of View Installation Tilt rotation Installation Recording Setting up Installing the Camera Unit 46 mm Change of Dome Cover Dome replacement Connecting to a Video Monitor Connecting to a Video Monitor When power is supplied from a PoE compatible hub, etc About the Power Select SwitchWhen power is supplied from an AC24V or DC12V power source Line-Lock control Video Switcher CAMERA1 Line Lock Phase Back Light Compensation Adjusting a LensMode Setting Switch Auto White Balance AWB Requirements for Network Camera Monitoring System Setting Up the Network Camera Environment Entering an IP Address Manually About the IP AddressObtaining an IP address automatically from the Dhcp server Structure of Connection Set the IP address of the personal computer Connecting Connect a LAN cable and then turn the power on Using Camera Finder to Search for a Camera Click the camera you want to login from the list of camerasSetting up Camera Finder Click Exit button to close Camera Finder Click the User button Click Admin on the left side of the screen Changing Administrator Login ID and Password Click the browser Click the Change button Click User on the left side of the screen Setting up Access Restriction Click the Set/Change button Click Network on the left side of the screen Configuring the Network Manually Click the Save button Select Manually Installation/Set up Viewing and Operation Close the browser to log off disconnect the camera ViewingViewing Images Camera Window Screen Menu that is displayed when right-clicking on the image Adjusting Images on the Camera OperationViewing Adding Images Click View log on the left side of the Camera Window screen Viewing Logs OperationViewing Recording About Recording Images Recordable Media Recordable Contents Click FTP client on the left side of the screen Recording Images on FTP Server FTP General Settings Configure each setting items Connection to FTP Enable Click the Save Settings button below the setting Periodic FTP by Schedule Configure recording schedule Enter File Name FTP by Motion Detection Configure settings for viewing FTP status File Transfer Order Click Image Recording Setting up Recording Click the Start button Recording Images on a Personal Computer Specify the destination folder and file name Click Save Current Picture As Recording Setting up Configure each item How to Set up Changing the camera name System SettingsClick System on the left side of the screen Setting the color of date/time display Setting up a format to display date/timeChanging the time using an NTP server setting Adjusting the date and time Click Export current configurations Rebooting the network cameraImporting the Settings Saved on a Personal Computer Updating the Firmware Displaying the screen asking a user name and password User Settings Deleting a user name Storing the user name and password Admin Settings Restarting the camera Changing the Administrator ID and password Click Alarm on the left side of the screen Alarm Settings Setting the motion detection Setting the motion detection Configuring the connection Network Settings Framerate Control Configuring the Http port numberDNS update to DNS 1/2 Server Click Mail on the left side of the screen Mail Settings Configure each item For details, refer to Recording Images on FTP Server → FTP Client Settings Click Ddns on the left side of the screen Ddns Settings Before Starting Updating the Firmware Click Upload button on the screen shown in Step Click Firmware updateClick the Browse button Specify the destination and then save the file Click Export current configurations Click Import on the screen shown in Step Select the file on settings you saved Setting up Others Index Glossary Safety Precautions3 Jpeg Up and OperationViewing Display of Logs Recording Setting up Before Calling Service Personnel Guide of your broadband router Before Calling Service Personnel... Symptom Cause How to Manage Cannot perform Lost the power RAM Sometimes primary is described as master Symptom Cause How to Manage Recorded Others IK-WR01A Specifications Appearance Diagram 150 Mounting Base Bracket Toshiba America Information SYSTEMS. INC