Die-cutting Front panel slit | Toshiba RAS-13UAV-E2, RAS-13UKV-E2

9-2-4. Wiring connection

Wiring of the connecting cable can be carried out without removing of the front panel.

1. Remove the air inlet grille.

FILE NO. SVM-03008

9-2-5. Piping and drain hose installation

*Since dewing results in a machine trouble, make sure to insulate both the connecting pipes. (Use polyethylene foam as insulating material.)

	Open the air inlet grille upward and pull it toward
	you.
2.	Remove the terminal cover and cord clamp.
3.	Insert the connecting cable (according to the local
	cords) into the pipe hole on the wall.
4.	Take out the connecting cable through the cable
	slot on the rear panel so that it protrudes about
	15 cm from the front.
5.	Insert the connecting cable fully into the terminal
	block and secure it tightly with screws.
6.	Tightening torque : 1.2 N·m (0.12 kgf·m)
7.	Secure the connecting cable with the cord clamp.

Rear right

Rear left

Bottom left

Left

Bottom right

Right

Front panel slit

Die-cutting

Changing drain hose

Piping preparation

8. Fix the terminal cover, rear plate bushing and air

inlet grille on the indoor unit.

CAUTION

•Be sure to refer to the wiring system diagram labeled inside the front panel.

•Check local electrical cords and also any specific wiring instructions or limitations.

Terminal block

Terminal cover

Fig. 9-2-8

1. Die-cutting Front panel slit

Cut out the slit on the left or right side of the front panel for the left or right connection and the slit on the bottom left or right side of the front panel for the bottom left or right connection with a pair of nippers.

2. Changing drain hose

For left connection, bottom-leftward connection and rear-leftward connection’s piping, it is necessary to change the drain hose and drain cap.

Connecting cable

Cord clamp

Screw

		Earth line
Screw	Screw	Connecting cable
	Screw

<How to remove the Drains Cap>

Clip drain cap by needle-nose pliers, and pull out.

Fig. 9-2-9

Fig. 9-2-6

80 mm

Earth line

10 mm

50 mm

NOTE:

•Wire type : More than H07RN-F or 245 IEC66 (1.0 mm2 or more)

Fig. 9-2-7 Stripping length of connecting cable

<How to install the Drain Hose>

Firmly insert drain hose connecting part until hitting on a heat insulator.

Heat insulator

Drain hose

Fig. 9-2-10

– 45 –

RAS-13UAV-E2, RAS-13UKV-E2 specifications

The Toshiba RAS-13UKV-E2 and RAS-13UAV-E2 air conditioning units represent a significant step forward in both comfort and energy efficiency. Designed for residential and light commercial use, these models are packed with features that cater to diverse climate control needs while adhering to modern standards of sustainability.

One of the standout features of both models is the implementation of inverter technology. This advanced system allows for more precise temperature control by adjusting the compressor speed based on the ambient temperature requirements. This not only enhances energy efficiency but also ensures a quieter operation compared to traditional air conditioning systems. As a result, users benefit from consistent comfort without the disruptive sounds often associated with cooling units.

The RAS-13UKV-E2 and RAS-13UAV-E2 also feature a high energy efficiency rating, which is crucial for reducing electricity bills. The Seasonal Energy Efficiency Ratio (SEER) is a vital measure of energy efficiency over an entire cooling season. Both units excel in this regard, making them an environmentally friendly choice. This is further supported by Toshiba's commitment to incorporating R32 refrigerant, known for its lower environmental impact compared to older refrigerants.

User convenience is enhanced with integrated smart controls. Both models are compatible with wireless remote control features, allowing for easy adjustments from a distance. This is complemented by programmable settings that let users schedule operation times, ensuring that the units run only when needed, which further optimizes energy consumption.

Design-wise, these air conditioners boast a sleek and modern appearance, making them a visually appealing addition to any room. They are constructed with durable materials that ensure longevity and reliability. Moreover, the filters are designed for easy maintenance, ensuring cleaner indoor air quality and prolonging the lifespan of the unit.

The Toshiba RAS-13UKV-E2 and RAS-13UAV-E2 units also come equipped with advanced air purification technologies. These features help to reduce airborne pollutants and allergens, contributing to a healthier indoor environment. With exceptional cooling and heating capabilities, easy installation, and advanced features, these models are designed to meet the modern user's needs for comfort, efficiency, and health. Overall, they represent an excellent investment in both cooling technology and eco-friendly practices.

Toshiba RAS-13UAV-E2, RAS-13UKV-E2 service manual Die-cutting Front panel slit, Changing drain hose

Models: RAS-13UAV-E2 RAS-13UKV-E2