9-2. Indoor Unit

9-2-1. Installation place

A place which provides the spaces around the indoor unit as shown in the above diagram.

A place where there is no obstacle near the air inlet and outlet.

A place that allows easy installation of the piping to the outdoor unit.

A place which allows the front panel to be opened.

The indoor unit shall be installed as top of the indoor unit comes to at least 2 m height.

Also it must be avoided to put anything on the top of the indoor unit.

CAUTION

Direct sunlight to the indoor unit’s wireless receiver should be avoided.

The microprocessor in the indoor unit should not be too close to RF noise sources.

(For details, see the owner’s manual.)

<Remote controller>

A place where there are no obstacles such as a curtain that may block the signal from the indoor unit.

Do not install the remote control in a place exposed to direct sunlight or close to a heating source, such as a stove.

Keep the remote control at least 1 m apart from the nearest TV set or stereo equipment. (This is necessary to prevent image disturbances or noise interference.)

The location of the remote control should be determined as shown below.

 

(Side view)

(Top view)

 

 

 

5

unit

 

 

 

 

m

 

7 m

 

Indoor unit

5

 

m

 

 

 

 

 

 

 

 

*7 m

Indoor

 

 

 

 

45°

 

 

 

 

 

 

4

°

 

 

 

 

 

 

5

 

°

 

 

 

 

 

 

 

75

 

 

 

 

 

 

 

Reception

Remote

Reception

 

 

 

range

 

 

 

Remote

 

control

 

 

 

 

range

 

 

 

 

 

control

 

 

 

* : Axial distance

 

 

Fig. 9-2-1

FILE NO. SVM-03008

9-2-2. Cutting a hole and mounting installation plate

<Cutting a hole>

When installing the refrigerant pipes from the rear.

Pipe hole

65 mm

The center of the pipe

 

hole is above the arrow.

100 mm

 

Fig. 9-2-2

1.After determining the pipe hole position on the mounting plate (A), drill the pipe hole (65 mm) at a slight downward slant to the outdoor side.

NOTE:

When drilling a wall that contains a metal lath, wire lath or metal plate, be sure to use a pipe hole brim ring sold separately.

<Mounting the installation plate>

For installation of the indoor unit, use the paper pattern on the back.

Anchor bolt holes

62

82.5

Hook

 

170

fromfloor

85

moreorm

 

 

 

Hook

 

1

2

 

 

 

 

Hook

 

Pipe

Installation

 

 

Pipe hole

Thread

 

hole

plate

 

 

 

 

 

 

Indoor unit

 

Weight 7 Mounting screw

 

Fig. 9-2-3

– 43 –

Page 44
Image 44
Toshiba RAS-13UAV-E2, RAS-13UKV-E2 Installation place, Remote controller, Cutting a hole, Mounting the installation plate

RAS-13UAV-E2, RAS-13UKV-E2 specifications

The Toshiba RAS-13UKV-E2 and RAS-13UAV-E2 air conditioning units represent a significant step forward in both comfort and energy efficiency. Designed for residential and light commercial use, these models are packed with features that cater to diverse climate control needs while adhering to modern standards of sustainability.

One of the standout features of both models is the implementation of inverter technology. This advanced system allows for more precise temperature control by adjusting the compressor speed based on the ambient temperature requirements. This not only enhances energy efficiency but also ensures a quieter operation compared to traditional air conditioning systems. As a result, users benefit from consistent comfort without the disruptive sounds often associated with cooling units.

The RAS-13UKV-E2 and RAS-13UAV-E2 also feature a high energy efficiency rating, which is crucial for reducing electricity bills. The Seasonal Energy Efficiency Ratio (SEER) is a vital measure of energy efficiency over an entire cooling season. Both units excel in this regard, making them an environmentally friendly choice. This is further supported by Toshiba's commitment to incorporating R32 refrigerant, known for its lower environmental impact compared to older refrigerants.

User convenience is enhanced with integrated smart controls. Both models are compatible with wireless remote control features, allowing for easy adjustments from a distance. This is complemented by programmable settings that let users schedule operation times, ensuring that the units run only when needed, which further optimizes energy consumption.

Design-wise, these air conditioners boast a sleek and modern appearance, making them a visually appealing addition to any room. They are constructed with durable materials that ensure longevity and reliability. Moreover, the filters are designed for easy maintenance, ensuring cleaner indoor air quality and prolonging the lifespan of the unit.

The Toshiba RAS-13UKV-E2 and RAS-13UAV-E2 units also come equipped with advanced air purification technologies. These features help to reduce airborne pollutants and allergens, contributing to a healthier indoor environment. With exceptional cooling and heating capabilities, easy installation, and advanced features, these models are designed to meet the modern user's needs for comfort, efficiency, and health. Overall, they represent an excellent investment in both cooling technology and eco-friendly practices.