Sub-menu of selected items appears | Toshiba TLPX10E specs

FULL MENU adjustments and settings – Picture (continued)

CONTENTS

58

When selecting “Signal format”, “Video mode” or “Interval” in step 2.

	Remote control				Control panel
	Remote control			(Main unit side)
				(Main unit side)
					AUTO	AUTO
	INPUT		ON/STANDBY		KEYSTONE	SET
		LASER
	KEYSTONE	AUTO	SET		VOL/ADJ.
	KEYSTONE		SET		VOL/ADJ.
	L-CLICK		R-CLICK			3-c
	VOLUME/ADJUST				ENTER	EXIT
					ENTER	EXIT
				3-c		3-c
				3-c	MENU	INPUT
					MENU	INPUT
	MENU	ENTER EXIT		3-c		ON/STANDBY
	PIP	FREEZE		3-c
	CALL	MUTE	RESIZE		TEMP LAMP ON
	CALL	MUTE

					BUSY	FAN

3-cENTER

ENTER

Press ENTER.

The sub-menu of selected items appears.

“Signal format”

“Video mode”

Y/PB/PR

Video

Picture

Picture

Video mode

Signal format

Auto.

NTSC

Auto.

PAL

480i

SECAM

480p

PAL-M

720p

PAL-N

1080i

PAL60

NTSC4.43

MENU QUICK

Select

EXIT Back

MENU QUICK

Select

EXIT Back

“Interval”

Memory card

Picture

Interval

10sec.

30sec.

3min. 10min.

MENU QUICK

Select

EXIT Back

Use the selection buttons ( / ) to select setting items.

Signal format (Y/PB/PR input)

Auto: Determine the type of the signal input automatically.

If not determined properly, select among the signals shown below. 480i, 480p, 720p, 1080i

Video mode (Video input, S-video input)

Auto: Determine the type of the signal input automatically.

If not determined properly, select among the signals shown below.

NTSC, PAL, SECAM, PAL-M, PAL-N, PAL60, NTSC4.43

Settings	Adjustments
	&

Continued

Image 58

Toshiba TLPX10E owner manual Use the selection buttons / to select setting items, Sub-menu of selected items appears

Contents

TLP-X10E Safety Precautions Avoid Volatile Liquid Save Original Packing MaterialsMoisture Condensation Source of Light Power SourcesVentilation Important Safety Instructions Do not place the product vertically AccessoriesObject and Liquid Entry Stack Inhibited Replacement Parts Important Safety InstructionsDamage Requiring Service Servicing Do not move the projector while the arm is still erect Safety CheckDo not carry by the camera arm Strong light may cause damage to your eyes or sight Power supply cord selection Contents Names of each part on the main unit Use VOL/ADJ buttons 30 41 48 Control connector RS-232C Connector 26 USB connector Use Names of each part on the remote control Laser emission part Open the cover Install the batteriesLoading batteries Attach the cover Remote control operation About Floor-mounted projector placement Determine the screen size projected on the screen Side view Take off the lens cover Connect the power cordInsert the other end in a wall outlet Projector placement angle adjustment Turn clockwise to lift up Turn counterclockwise to lower Ceiling-mounted projector placement Installation and connection Connecting a computer Connecting a computer with DVI output connector Computer in 2 Connector DVI connector Connecting video equipment RGB2/digital RGB and Y/P B/P R input Projector operation control by a computer How to use the output connector Press ON/STANDBY Playback modeProjection on the screen Turn on the connected equipment and put it Signal sent from the computer Select the input source Press VOL/ADJ +/ to adjust volume Adjust the picture size by turningFocusing ring Zooming lever Press ON/STANDBY after using the projector Turning the power offPress ON/STANDBY again Adjusting the picture automatically Press Auto SET Correcting the keystone distortion Press Auto Keystone Press Mute Remote controlCutting off the picture and sound temporarily Operations Press Freeze Icon Appears in the freeze modeFreezing the picture Picture freezes Enlarging the picture size Icon Appears in the resize modePress Resize Press PIP Displaying PIP Sub-picturesSub-picture is displayed Information described below is displayed Displaying InformationPress Call Pressed again Operating a computer by the remote control Projecting images stored in a memory card About memory cards Insert the memory card into the card slot Press Input repeatedly to select the memory card input Use VOL/ADJ +/ to change pages. Remote control Control panelDescription of screen Changing Press VOL/ADJ +/-. Slide transition Press ENTER. Slide displayPress Exit Projecting images stored in a memory card To eject the memory card Adjustments and settings on the menu screen Quick Menu Adjustments and settings on the menu screen Operating the menu screen Start Press Menu Quick Menu adjustments and settingsQuick Menu appears Types of adjustment and setting items are different See the table below Lamp power Press VOL/ADJ +/ to adjust and setPicture mode Analog RGB input, digital RGB input Auto. demo Memory card input Press VOL/ADJ +/- to select the type of input source Sub-menu screen of input source setting appearsPress Enter Press Exit to return to the Quick Menu Use the selection buttons / to select a language Use the selection buttons / to select interval time Sub-menu screen of interval setting appearsMenu screen disappears Adjustments Full Menu adjustments and settings -PicturePress Menu twice Full Menu adjustments and settings Picture Screen size Picture mode RGB inputInput select mode Memory card input Slide show Memory card input Press Exit to return to the Full Menu Sub-menu of selected items appears PositionLevel Video mode Video input, S-video input Use the selection buttons / to select setting itemsSignal format Y/PB/PR input Sub-menu of selected items appears Full Menu adjustments and settings Picture Full Menu settings Audio Channel select After the settings are finished, press ExitSpeaker output Loudness Use the selection buttons To select Setting items Full Menu settings KeystoneUse the selection buttons To display Keystone menu Press Exit several times until the menu screen After the adjustments and settings are finishedUse the selection buttons / to select Yes and press Enter Disappears When pressed once, the Quick Menu screen appears. When Full Menu settings DisplayUse the selection buttons To select Setting items Settings Use the selection buttons To display Display menu When selecting Language in step Menu background translucent No signal background Setting of screen of no signal inputMenu position Start-up screen Use the selection buttons To display Default setting menu Full Menu settings Default settingWhen pressed once, the Quick Menu screen appears. When Sub-menu of Input source setting appears Control panel Main unit side Sub-menu of Projection mode appears Use the selection buttons / to select the projection modeRear ceiling Ceiling-mounted rear projection Power on No signal power offPress VOL/ADJ +/ to set Factory default setting Full Menu settings Factory reset modePicture menus for the each input to Full Menu settings Factory reset mode Audio Set the audio input source PIP menu settingSize Set the PIP sub-picture size Menu screen disappears Part names of the document imaging camera model Preparation of the document imaging camera Camera control panel Press ARM LightSet a document to be projected Light turns on Press Camera to select the camera input mode Move the camera head to adjust the size Picture Follow the steps of Preparation of the document imaging Press Camera Gain +/- to improve view of aCamera subject which is too dark or vivid Camera in reverse Project a white paper and enlarge it to fill Balance Press W.BALANCE to turn the Lock indicatorLock the white balance Screen Cover the camera lens with a piece of black Correcting illuminated defectsWith the document camera operating, fully Paper or cloth Store the camera images into the memory card Power turns off or does not come on IndicatorPower does not come on Trouble indications Clean the air filter Air filter cleaningUnplug the power cord Take off the air filter cover Assemble the air filter Air filter cleaningInstall it Mount the air filter cover Cleaning the main unit Lens and main unit cleaningCleaning the lens Replacing the intake, exhaust fans and air filter Loosen two screws, and pull off the lamp cover Lamp replacementPull out the lamp Handle to pull out the lamp Attach the lamp cover Reset the lamp timerLoad a new lamp Slide the cover in place and tighten two screws Before calling service personal Symptom Cause Correction Before calling service personal Pin assignment of Computer IN, Monitor OUT connector Applicable signal Applicable RGB signal Applicable signal Compatible video signal Controlling the projector by using RS-232C Signal assignment of RS-232C Interface format Controlling the projector by using RS-232C AS1 MB1 VLU Auto SET Mini DIN 8-pin RS-232C SpecificationsUSB output Type B Specifications Replacement lamp