Projection on the screen, Press ON/STANDBY | Toshiba TLPX10E

Projection on the screen

CONTENTS

28

CAUTION – Do not look into the projection lens while operating the projector.

Control panel

Remote control				(Main unit side)
				(Main unit side)
			1	AUTO	AUTO
INPUT		ON/STANDBY	1	KEYSTONE	SET
	LASER
KEYSTONE	AUTO	SET		VOL/ADJ.
KEYSTONE		SET		VOL/ADJ.

L-CLICK	R-CLICK
VOLUME/ADJUST		ENTER	EXIT
		ENTER	EXIT
		MENU	INPUT
MENU	ENTER EXIT		ON/STANDBY	1
PIP	FREEZE			1
CALL	RESIZE
CALL	MUTE	TEMP LAMP ON		1
		TEMP LAMP ON
		BUSY	FAN

Indicators

Preparation

1Install and connect the projector properly.

2Take off the lens cover.

1		Press ON/STANDBY.
		Press ON/STANDBY.
		The projector turns on and the ON, LAMP and FAN indicators
		light in green.
		light in green.
		(The LAMP indicator blinks while the lamp is warming up.)

LAMP	ON	LAMP	ON
(Green)	(Green)	(Green)	(Green)
Flashing	FAN		FAN
	(Green)		(Green)

The lamp lights and the start up display appears.

2	Turn on the connected equipment and put it in
	playback mode.

Operations

Select “Cancel” when the dialog box of Add New Hardware Wizard screen appears on the computer.

Continued

Image 28

Toshiba TLPX10E Projection on the screen, Press ON/STANDBY, Turn on the connected equipment and put it, Playback mode

Contents

TLP-X10E Safety Precautions Avoid Volatile Liquid Save Original Packing MaterialsMoisture Condensation Source of Light Power SourcesVentilation Important Safety Instructions Accessories Object and Liquid EntryDo not place the product vertically Stack Inhibited Important Safety Instructions Damage Requiring ServiceReplacement Parts Servicing Safety Check Do not carry by the camera armDo not move the projector while the arm is still erect Strong light may cause damage to your eyes or sight Power supply cord selection Contents Names of each part on the main unit Use VOL/ADJ buttons 30 41 48 Control connector RS-232C Connector 26 USB connector Use Names of each part on the remote control Laser emission part Install the batteries Loading batteriesOpen the cover Attach the cover Remote control operation About Floor-mounted projector placement Determine the screen size projected on the screen Side view Take off the lens cover Connect the power cordInsert the other end in a wall outlet Projector placement angle adjustment Turn clockwise to lift up Turn counterclockwise to lower Ceiling-mounted projector placement Installation and connection Connecting a computer Connecting a computer with DVI output connector Computer in 2 Connector DVI connector Connecting video equipment RGB2/digital RGB and Y/P B/P R input Projector operation control by a computer How to use the output connector Playback mode Projection on the screenPress ON/STANDBY Turn on the connected equipment and put it Signal sent from the computer Select the input source Adjust the picture size by turning Focusing ringPress VOL/ADJ +/ to adjust volume Zooming lever Press ON/STANDBY after using the projector Turning the power offPress ON/STANDBY again Adjusting the picture automatically Press Auto SET Correcting the keystone distortion Press Auto Keystone Remote control Cutting off the picture and sound temporarilyPress Mute Operations Icon Appears in the freeze mode Freezing the picturePress Freeze Picture freezes Enlarging the picture size Icon Appears in the resize modePress Resize Press PIP Displaying PIP Sub-picturesSub-picture is displayed Displaying Information Press CallInformation described below is displayed Pressed again Operating a computer by the remote control Projecting images stored in a memory card About memory cards Insert the memory card into the card slot Press Input repeatedly to select the memory card input Remote control Control panel Description of screenUse VOL/ADJ +/ to change pages. Changing Press VOL/ADJ +/-. Slide transition Press ENTER. Slide displayPress Exit Projecting images stored in a memory card To eject the memory card Adjustments and settings on the menu screen Quick Menu Adjustments and settings on the menu screen Operating the menu screen Start Press Menu Quick Menu adjustments and settingsQuick Menu appears Types of adjustment and setting items are different See the table below Press VOL/ADJ +/ to adjust and set Picture mode Analog RGB input, digital RGB inputLamp power Auto. demo Memory card input Sub-menu screen of input source setting appears Press EnterPress VOL/ADJ +/- to select the type of input source Press Exit to return to the Quick Menu Use the selection buttons / to select a language Use the selection buttons / to select interval time Sub-menu screen of interval setting appearsMenu screen disappears Adjustments Full Menu adjustments and settings -PicturePress Menu twice Full Menu adjustments and settings Picture Picture mode RGB input Input select mode Memory card inputScreen size Slide show Memory card input Press Exit to return to the Full Menu Sub-menu of selected items appears PositionLevel Use the selection buttons / to select setting items Signal format Y/PB/PR inputVideo mode Video input, S-video input Sub-menu of selected items appears Full Menu adjustments and settings Picture Full Menu settings Audio After the settings are finished, press Exit Speaker outputChannel select Loudness Use the selection buttons To select Setting items Full Menu settings KeystoneUse the selection buttons To display Keystone menu After the adjustments and settings are finished Use the selection buttons / to select Yes and press EnterPress Exit several times until the menu screen Disappears Full Menu settings Display Use the selection buttons To select Setting items SettingsWhen pressed once, the Quick Menu screen appears. When Use the selection buttons To display Display menu When selecting Language in step No signal background Setting of screen of no signal input Menu positionMenu background translucent Start-up screen Use the selection buttons To display Default setting menu Full Menu settings Default settingWhen pressed once, the Quick Menu screen appears. When Sub-menu of Input source setting appears Control panel Main unit side Sub-menu of Projection mode appears Use the selection buttons / to select the projection modeRear ceiling Ceiling-mounted rear projection Power on No signal power offPress VOL/ADJ +/ to set Factory default setting Full Menu settings Factory reset modePicture menus for the each input to Full Menu settings Factory reset mode PIP menu setting Size Set the PIP sub-picture sizeAudio Set the audio input source Menu screen disappears Part names of the document imaging camera model Preparation of the document imaging camera Press ARM Light Set a document to be projectedCamera control panel Light turns on Press Camera to select the camera input mode Move the camera head to adjust the size Picture Press Camera Gain +/- to improve view of a Camera subject which is too dark or vividFollow the steps of Preparation of the document imaging Camera in reverse Balance Press W.BALANCE to turn the Lock indicator Lock the white balanceProject a white paper and enlarge it to fill Screen Correcting illuminated defects With the document camera operating, fullyCover the camera lens with a piece of black Paper or cloth Store the camera images into the memory card Indicator Power does not come onPower turns off or does not come on Trouble indications Air filter cleaning Unplug the power cordClean the air filter Take off the air filter cover Air filter cleaning Install itAssemble the air filter Mount the air filter cover Lens and main unit cleaning Cleaning the lensCleaning the main unit Replacing the intake, exhaust fans and air filter Lamp replacement Pull out the lampLoosen two screws, and pull off the lamp cover Handle to pull out the lamp Reset the lamp timer Load a new lampAttach the lamp cover Slide the cover in place and tighten two screws Before calling service personal Symptom Cause Correction Before calling service personal Pin assignment of Computer IN, Monitor OUT connector Applicable signal Applicable RGB signal Applicable signal Compatible video signal Controlling the projector by using RS-232C Signal assignment of RS-232C Interface format Controlling the projector by using RS-232C AS1 MB1 VLU Auto SET Mini DIN 8-pin RS-232C SpecificationsUSB output Type B Specifications Replacement lamp