Tunturi T50 owner manual I N T E N a N C E

O W N E R ' S M A N U A L • T 5 0

will remain in the meter's memory until replaced with a new one.

4. Press Enter and set the user weight using the arrow keys. Press Enter again to confirm your selection The setting will remain in the meter's memory until replaced with a new one.

5.Press Start. The exercise begins and the belt starts moving.

6. You can scale the the profile speed level up and down at 5% steps using the arrow keys.

7.Press Stop/Pause and the treadmill stops and moves into waiting state for 5 minutes. You can restart the interrupted exercise by pressing the Start key within 5 minutes. Press Stop/Pause twice to end your exercise. Keep the Stop key pressed down for 2 seconds to reset the meter. The meter then switches to its initial state.

If the profile duration and user weight do not need to be adjusted, you can start the exercise by selecting the Hill profile you want and pressing Start.

M A I N T E N A N C E

The equipment is safe to use only when periodically maintained and inspected for faults and wear. CAUTION! Do not attempt any servicing or adjustment other than those described in this manual. Any other servicing must be performed by an authorized service representative. Check the tightness of all fixing screws once a year. Do not overtighten. Defective components must be immediately replaced; the equipment must not be operated with any defective components.

LUBRICATING THE RUNNING DECK

Lubrication is the most important service activity for the treadmill. This is absolutely essential, if the friction of the running deck increases noticeably or the motor begins to heat up; increased friction is indicated by jerky movement of the belt. Insufficient lubrication will cause the belt, running deck and motor to wear out and break. The need for re-lubrication depends to a great extent on the running styles and weight of the user: heavy user weight and slow speed put particular strain on the device and therefore demand greater lubrication. The running deck requires periodic lubrication. With average usage (30 minute workout session 3 times a week), lubricate every four to six months. You may adjust the timing of the lubrication based on the intensity of the treadmill use level. To check the lubrication level, simply lift the running belt, and put your hand as far into the center of the belt as you can reach. If your hand shows signs of lubricant (some wetness), then it does not need additional lubrication. If the board feels dry and there is very little evidence of lubricant on your hand, then additional lubrication should be added as instructed:

1.Stop running belt so belt seam is located on the top and in the center of the deck.

2. Insert nozzle into spray head of lubricant can.

3. Lift running belt.

4. Position nozzle between the belt and the board approximately 200 mm (8") from the front of the treadmill.

5.Apply T-Lube from the front to the rear of the treadmill on each side of the treadmill. Try to reach the spray as far into the center of the running deck as possible.

6. The treadmill is instantly ready for use.

NOTE! Lubricate your treadmill only with T-Lube lubricant. Contact your local Tunturi distributor for supplies of T-Lube.

CLEANING THE TREADMILL

Wipe the treadmill surfaces, especially the handlebars and meter from dust with a damp cloth or towel. Do not use solvents. Use a small vacuum nozzle to carefully vacuum around all visible components (belt, running deck, side rails etc.). To clean the underside of the treadmill, lift the running deck to the storage position.

NOTE! Also keep the area near the treadmill clean. While in use, the treadmill gathers dust that may cause problems in the operation of the equipment.

ALIGNING THE RUNNING BELT

Monitor belt tracking during exercise and make adjustments as needed. The belt should run in the center of the treadmill. Alignment is not usually needed, provided

•the treadmill is placed on an even, solid and horizontal surface and the belt is correctly tensioned

•the alignment of the belt is correct

It is, however, possible for the belt to be pushed to one side due to the user's running style (e.g. more weight on one foot). The alignment of the belt is adjusted by turning the two bolts at the back of the treadmill.

Align the belt according to the following instructions:

1.Turn the power switch on and increase the treadmill's speed to 5 km/h (3 mph).

2. If the belt drifts to the left, turn the left adjustment bolt 1/4 turn clockwise and the right adjustment bolt 1/8 turn anti-clockwise. If the belt drifts to the right, turn the right adjustment bolt 1/4 turn clockwise and the left adjustment bolt 1/4 turn anti-clockwise.

3. If the belt remains centered the adjustment is correct. If not, continue to make small adjustments as above until the belt is correctly aligned. If the

8