running deck according to the following instructions:
A)Foldable frame
1.Attach the nozzle of the lubrication tube to the T- Lube S container.
2.Lift the running belt and lock it.
3.Position the nozzle between the belt and the board. Try to reach the spray as far into the center of the running deck as possible.
4.Spray the lubricant for 5 seconds.
5.Lower the running deck into its normal position. Let the belt run for at least a minute at 1,5 kph. This is done to lubricate the belt evenly.
NOTE! You should let the treadmill run at least five minutes before lifting the running deck to the storage position. This will prevent the lubricant from spilling.
B)Solid frame
1.Attach the nozzle of the lubrication tube to the T- Lube S container.
2.Adjust the running deck to its maximum elevation (10 %).
3.Position the nozzle between the belt and the board. Try to reach the spray as far into the center of the running deck as possible.
4.Spray the lubricant for 5 seconds.
5.Lower the running deck into its normal position. Let the belt run for at least a minute at 1,5 kph. This is done to lubricate the belt evenly.
NOTE! Lubricate your treadmill only with T-Lube S silicon lubricant. Contact your local Tunturi distributor for further supplies of T-Lube.
ALIGNING THE RUNNING BELT
Monitor belt tracking during exercise and make adjustments as needed. The belt should run in the center of the treadmill. Alignment is not usually needed, provided
•the treadmill is placed on an even, solid and horizontal surface and the belt is correctly tensioned
•the alignment of the belt is correct
It is, however, possible for the belt to be pushed to one side due to the user’s running style (e.g. more weight on one foot). The alignment of the belt is adjusted by turning the two bolts at the back of the treadmill.
ALIGN THE BELT ACCORDING TO THE FOLLOWING INSTRUCTIONS:
1.Turn the power switch on and increase the treadmill’s speed to 5 km/h (3 mph).
2.If the belt drifts to the left, turn the left adjustment bolt ¼ turn clockwise and the right adjustment bolt 1/8 turn anti-clockwise. If the belt drifts to the right, turn the right adjustment bolt ¼ turn clockwise and the left adjustment bolt ¼ turn anti-clockwise.
3.If the belt remains centered the adjustment is correct. If not, continue to make small adjustments as above
O W N E R ’ S M A N U A L • T 8 0 T 8 5
until the belt is correctly aligned. If the belt is allowed run across to one side for long periods of time the edges of the belt may be damaged and the treadmill may not continue to operate correctly. Any damage to the belt caused by the lack of necessary adjustment will not be covered by the warranty.
ADJUSTING THE BELT TENSION
The belt must be tensioned if it begins to slip on the rollers. In normal use, however, keep the belt as loose as possible! The belt tension is adjusted by turning the same screws as used for aligning the running belt. If turning the screws will not effect the belt tension, please contact your local Tunturi dealer.
1.Increase the treadmill’s speed to 5 km/h (3 mph).
2.Turn both adjustment screws an equal amount, ¼ turn clockwise.
3.Try to slow the belt down by holding onto the handrails and braking as you walk (as if you were walking downhill).
If the belt slips, turn another ¼ turn and repeat the test. When braking heavily the belt may slip. If the belt keeps slipping despite repeated adjustments, please contact your local Tunturi dealer.
MALFUNCTIONS
NOTE! Despite continuous quality control, defects and malfunctions caused by individual components may occur in the equipment. In most cases it’s unnecessary to take the whole device in for repair, as it’s usually sufficient to replace the defective part. Always give the model, serial number of your equipment and in case of malfunctions also conditions of use, nature of malfunction and any error code.
When you encounter unusual behavior from the treadmill, simply turn the power switch off, wait 1 minute and turn the power switch on to reset the treadmill. This should clear incidental errors and ready the treadmill for normal operation again. If after you have reset the treadmill by turning the power switch off and on again, and the treadmill is still not operational, contact your local Tunturi dealer for service.
If you require spare parts, always give the model, serial number of your equipment and the spare part number for the part you need. The spare part list is at the back of this manual. Use only spare parts mentioned in the spare part list.
ERROR CODES
The user interface will display information about operational faults.
SYSTEM CHECK FAILED. Possible motor controller fault. Turn the power switch off, wait 1 minute and turn the power switch on again. If treadmill recovers to normal operation, you may continue to use the treadmill. Otherwise, call the dealer for service.
SPEED SENSOR ERROR. Call the dealer for service.
