26 or | Ultimate Technology 600 POS specification

Table 2. Local Mode Programming Instructions

* = Default Settings

Function Code(s)	Operation	Normal Indication	Remarks

26 or 36	1. Swipe	Program Card. While in programming	mode, at the Series 600 Keyboard
Comm (RS232)	numeric keypad, enter applicable Function Code 26 (Port 0) or 36 (Port 1).
Main Port 0 (26)	LED (2) flashes.
AUX Port 1 (36)	LED (2) flashes.
AUX Port 1 (36)
Suffix	2. At the auxiliary keyboard, press the desired key or type the desired key sequence.

	Note that the maximum number of key codes is limited to 24 – this is equivalent to
	approximately 12 key strokes.
			If the Series 600 Keyboard beeps and
			LED (2) turns off while entering key
			codes at the auxiliary keyboard, you
			have exceeded 24 key codes.
			Repeat steps 1 and 2.

3.At the Series 600 Keyboard, press ENTER.

LED (2) turns off.

4.Program the next function code or exit programming mode by entering 99 on Series 600 Keyboard numeric keypad or by swiping the Program Card.

Series 600 POS Keyboard

22

Image 27

Ultimate Technology 600 POS manual 26 or

Contents

Programming & USER’S Guide Table of Contents Maintenance Appendix List of TablesList of Figures Series 600 POS Keyboard Special Note Scope Series 600 POS Keyboard Features Product InformationModel Description BUILT-IN Annunciator BUILT-IN Diagnostics Environment Service and WarrantySpecifications Weight Approvals Unpacking and Inspection Installation Driver 1 External ConnectionsCash Drawer Jumper Connections Printer Fired Printer 1, 2 Pinouts Main RS232 Typical Keyboard External Connections Description Keyboard External Connectors Rear View Operation Controls and Indicators Series 600 POS Keyboard Local Mode Programming Instructions ProgrammingProgramming Keyboard Operating Parameters LED 2 turns on LED 2 flashesLED 2 stops flashing LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 21 or 20 or 23 or 22 or 25 or 24 or 26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Break Series Keyboard Description Numeric Keypad no Example Example Programming in Remote Mode Series 600 POS Keyboard Acknowledgement None Command A0krcCxDx.......CR Command A1aCxDx.......CR Commp Command A6xCR Clicked CommandA4xxxx-xxxxCR A5xCxDxCR Nvbdwr Command Nvbdclr Command A9CLRCRCdsecopn AExCR Secure CommandComment Command ADxCR Command B0LxCR B2p...........CR B1pdCR Commit Command Command B5RSTCRKssnd Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEX Msrsnd CommandCarded Command Cdcont Command BApCRBBpCR BDpxCR Porte CommandBCpCR Acknowledgement BF...............CR Command Bfcr101/102-KEY Keyboard KEY Code Identification BEnnnnnvvvvkkkkx-xCR Remote Programming KEY MAKE/BREAK Codes Remote Description Programming Command Examples of Remote Programming for KEY MAKE/BREAK Code Where A0 Example Example Opos Opos Programming Suffix MSR Programming for UTC Opos DriversTrack Prefix MSR Series Copying Keyboard Setup Data CloningSource Unit Destination Unit Series 500 Main System LOG Operators and Programmers Magnetic Cards Maintenance PrecautionsCleaning KEY Legend Change Inch Full Travel Keyboards Battery Replacement Series 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Series 600 POS Standard Keyboard Layouts Appendix a Back Connector Pinouts Appendix B Keyboard CABLE/CONNECTOR Data DLE Appendix C Ascii Character SET Decimal Hexadecimal Scan Code KEY Number 2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 VICTOR, NEW York Ultimate Technology Corporation