Connect the printer and IC unit | Ultra electronic ID Card Printer

(to the next page)

Connecting the IC unit

(sold separately)

Large and compact size IC units are sold separately, as are specialized optional devices for the unit. Consult your dealer for more details.

WARNING

⬤Make sure that the power switch is turned OFF and the AC cable is detatched from the plug, before connecting and

Electric	disconnecting the IC units. Otherwise
shock	electric shocks, fires or malfunction of the
	product may occur.

⬤Using IC units other than those specified may cause electric shocks, fires or malfunction of the product.

Large size IC unit (sold separately)

1. A joint plate for an IC unit is provided as an accessory.

2. Fit the printer and IC unit into the holes as shown.

CX21ICL*

3. Connect the printer and IC unit.

Connect the cable which comes with the IC unit to the OPTION 1 terminal.

Connecting to the PRT interface terminal

Connection cable (Accessory)

Use the OPTION 1 side. If you use side 2 it does not function.

4. Connect the IC unit with the host computer.

Connect interface cables which are commercially available.

The terminal is rotated 180°

Commercial item

Terminals on the rear of the IC unit SERIAL1:non-contact SERIAL2:contact

CX21ICL* is manufactured by Victor Data Systems Company of Japan, Limited.

CAUTION

Unstable locations and angled surfaces may cause card feeder malfunctions. Make sure to fit the devices into the holes securely. Furthermore, install the printer on a flat and hard surface.

11

Image 12

Ultra electronic ID Card Printer manual Connecting the IC unit Sold separately, Connect the printer and IC unit

Contents

ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity For USA only Machine Noise Contents Do not touch the power plug during electrical Storms Do not use a line voltage other than instructedDo not wet the machine with water Do not touch the machine with wet hands Do not use the machine while it has a fault Pull out the power plug before cleaning MachineHold the body of the power plug when pulling it Out Do not touch the power plug with a wet hand Product features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cards Installation Names of parts Connecting with a host computer Set the BUS switchesSet-up Set the Scsi ID Connecting the IC unit Sold separately Connect the printer and IC unitConnect the IC unit with the host computer Connecting the power cord Plug the power cable into the printerCompact IC unit sold separately Connect the compact IC unit to the host computer Installing the card stacker Mount the card stacker on the printerHang the stacker claw on the stacker receptacle Discharging the card Setting the ink ribbon Remove the ink ribbon cassettePlace the cassette upright on a flat surface during set-up Wind the ribbon, taking up the slack When the ink ribbon is wound up to the end Insert the cassette along the guide railClose the printer door Setting the retransfer film Remove the retransfer film cassette Setting the number of frames to be used When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassette Setting cards Open the card tray Card bracket locks when it reaches the hole Inserting cards Unit can take about 300 0.76mm-thick cardsPull the card bracket back Close the card tray When using magnetic cards Loading cards When using contact IC cardsFor JIS II cards For ISO cards Switching the card thickness Remove the card thickness switching plateMalfunction of the printer Remove the blue securing screw Names of parts on the operation Panel Operation display LED contents LCD panel LCD operation display content Turning on the power Operation Turning off the power About the Reset buttonTurn off the printer’s power Initialized without winding up. Default User mode screen flow User modes User mode settings Main menu Submenu Display mode settings Cleaning mode Press Enter to resetExit user mode Clearing the free counter Ink mode setting Retransfer mode setting Set the retransfer temperatureSet retransfer film Set the retransfer speed Buzzer mode setting Setting the bend remedy mode Card size setting mode Antimagnetic setting modeTransport mode Test print Care and cleaning Cleaning the cleaning rollersRemove the cleaning unit Cleaning the thermal head Wipe the head indicated with horizontally Cleaning the fan filter on the back side How to attach the sponge Cleaning the card feed rollers Set a cleaning cardFrom user mode select cleaning mode Turn off the power after the cleaning card is discharged Cleaning the card feed rollers Heat rollers Once printer servicing and cleaning Have been completedApply alcohol on the magnetic head cleaning card Set the card on the card tray Troubleshooting Cleaning rollersLayout of rollers inside the printer Card turnover table Error code listing Meaning of reset → enter buttons in the list is Troubleshooting About printing errors Mending broken ink ribbon Retransfer film Removing card jams Return the card tray to its original positionPush the card tray back into position on an angle Remove any jammed cards Jog lever are supplied as standardTurn the jog dial Remove the card Specifications Main specifications External appearance and dimensions Front viewUnit/mm Ultra Electronics Card Systems