Installing the card stacker | Ultra electronic ID Card Printer

(to the next page)

Installing the card stacker

1. Mount the card stacker on the printer.

Hang the stacker claw on the stacker receptacle.

Card discharge slot

Claw	Card stacker
	receptacle
Card stacker
(accessory)

Discharging the card

When correctly printed, the cards are discharged from the left side.

If a card jam or a write error on magnetic stripes occurs on the way, results differ depending on the areas.

Portion A: If a card jam or a write error on magnetic stripes occurs on the way, press the RESET button, then the ENTER button. The printer is initialized, and the cards are discharged from the right side of the printer.

Portion B: See the description in Jam (Transfer) on p.45.

Portion C: When correctly printed, the cards are discharged from the left side of the printer. The cards jamming around this area are also discharged from the left side.

The card stacker is capable of containing approximately 100 0.76mm-thick cards or 280 0.25mm- thick cards at the maximum.

CAUTION

Be sure to hang the card stacker

claw on the card stacker receptacle, not the card discharge slot. If you mount the card stacker at a wrong place, cards are not discharged, resulting in a card jam.

Retransfer film cassette

Ink ribbon cassette

Thermal head

Magnetic head

Card turnover table

Feed roller

NG card discharge slot

Cleaning roller

Card feed roller

Retransfer roller (heat roller)

Bent remedial roller (heat roller)

C BA

13

Image 14

Ultra electronic ID Card Printer Installing the card stacker, Mount the card stacker on the printer, Discharging the card

Contents

ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity For USA only Machine Noise Contents Do not wet the machine with water Do not touch the power plug during electrical StormsDo not use a line voltage other than instructed Do not touch the machine with wet hands Hold the body of the power plug when pulling it Out Do not use the machine while it has a faultPull out the power plug before cleaning Machine Do not touch the power plug with a wet hand Before use Product featuresChecking accessories Handling of transfer film Ink ribbons and cards Installation Names of parts Set-up Connecting with a host computerSet the BUS switches Set the Scsi ID Connect the IC unit with the host computer Connecting the IC unit Sold separatelyConnect the printer and IC unit Compact IC unit sold separately Connecting the power cordPlug the power cable into the printer Connect the compact IC unit to the host computer Hang the stacker claw on the stacker receptacle Installing the card stackerMount the card stacker on the printer Discharging the card Place the cassette upright on a flat surface during set-up Setting the ink ribbonRemove the ink ribbon cassette Wind the ribbon, taking up the slack Close the printer door When the ink ribbon is wound up to the endInsert the cassette along the guide rail Setting the retransfer film Remove the retransfer film cassette Wind the retransfer film to take up the slack Setting the number of frames to be usedWhen the retransfer film is wound up to the end Open the printer door and insert the cassette Setting cards Open the card tray Pull the card bracket back Card bracket locks when it reaches the holeInserting cards Unit can take about 300 0.76mm-thick cards Close the card tray For JIS II cards When using magnetic cards Loading cardsWhen using contact IC cards For ISO cards Malfunction of the printer Switching the card thicknessRemove the card thickness switching plate Remove the blue securing screw Names of parts on the operation Panel Operation display LED contents LCD panel LCD operation display content Turning on the power Operation Turn off the printer’s power Turning off the powerAbout the Reset button Initialized without winding up. Default User mode screen flow User modes User mode settings Main menu Submenu Display mode settings Exit user mode Cleaning modePress Enter to reset Clearing the free counter Ink mode setting Set retransfer film Retransfer mode settingSet the retransfer temperature Set the retransfer speed Buzzer mode setting Setting the bend remedy mode Transport mode Card size setting modeAntimagnetic setting mode Test print Remove the cleaning unit Care and cleaningCleaning the cleaning rollers Cleaning the thermal head Wipe the head indicated with horizontally Cleaning the fan filter on the back side How to attach the sponge From user mode select cleaning mode Cleaning the card feed rollersSet a cleaning card Turn off the power after the cleaning card is discharged Apply alcohol on the magnetic head cleaning card Cleaning the card feed rollers Heat rollersOnce printer servicing and cleaning Have been completed Set the card on the card tray Layout of rollers inside the printer TroubleshootingCleaning rollers Card turnover table Error code listing Meaning of reset → enter buttons in the list is Troubleshooting About printing errors Mending broken ink ribbon Retransfer film Push the card tray back into position on an angle Removing card jamsReturn the card tray to its original position Turn the jog dial Remove any jammed cardsJog lever are supplied as standard Remove the card Specifications Main specifications Unit/mm External appearance and dimensionsFront view Ultra Electronics Card Systems