Operation, Turning on the power | Ultra electronic ID Card Printer

Operation

Turning on the power

1. Before turning on the power, check the following:

Make sure that the printer door is completely closed.

Make sure that the card tray is completely closed. Make sure that the host computer is correctly connected.

Make sure that any peripheral equipment is correctly connected.

Make sure that the power supply outlet is correctly connected.

Only switch the unit on after checking the above points.

*When operating this unit in the stand-alone mode, or if this unit is turned ON when a connected host computer has not yet been turned ON,

the LCD panel indication may freeze with Ver. xxx/xx/xx (the xx is varying according to the firmware version.)

This occurs because the SCSI bus is locked. If this occurs, turn OFF the power and return the bit 2 on the BUS switch to on the rear of the unit to the factory settings. Then turn ON the power again. For the factory settings, refer to p. 10 of this manual or the indication on the rear panel of the unit.

3. The unit will be in the ready status approximately 4 minutes after turning on the power.

The operation display LED (READY LED) will light up.

READY	RESET	MENU

ERROR

EXITENTER

CAUTION

Do not turn the power off while the LCD panel displays ‘Boot up’ to ‘Initializing’, as this may cause malfunctions.

2. Turn the power ON.

(I represents ON and represents OFF.)

Before turning on the host computer, make sure that the LCD panel displays Preheat or Ready.

Making settings in the user modes

When the LCD panel displays Ready or Preheating,

R e a d y

P r e h e a t i n g . .

OR

MENU

press button.

For details concerning each user mode setting, see p. 26 of this manual.

4. Enter the control command from the host computer to print cards.

The operation display LED (READY LED) will flash while the unit is receiving image data from the host computer.

READY

RESET

ERROR

EXIT

MENU

ENTER

24

Image 25

Ultra electronic ID Card Printer manual Operation, Turning on the power

Contents

ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity Machine Noise For USA only Contents Do not use a line voltage other than instructed Do not touch the power plug during electrical StormsDo not wet the machine with water Do not touch the machine with wet hands Pull out the power plug before cleaning Machine Do not use the machine while it has a faultHold the body of the power plug when pulling it Out Do not touch the power plug with a wet hand Checking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cards Installation Names of parts Set the BUS switches Connecting with a host computerSet-up Set the Scsi ID Connect the printer and IC unit Connecting the IC unit Sold separatelyConnect the IC unit with the host computer Plug the power cable into the printer Connecting the power cordCompact IC unit sold separately Connect the compact IC unit to the host computer Mount the card stacker on the printer Installing the card stackerHang the stacker claw on the stacker receptacle Discharging the card Remove the ink ribbon cassette Setting the ink ribbonPlace the cassette upright on a flat surface during set-up Wind the ribbon, taking up the slack Insert the cassette along the guide rail When the ink ribbon is wound up to the endClose the printer door Remove the retransfer film cassette Setting the retransfer film When the retransfer film is wound up to the end Setting the number of frames to be usedWind the retransfer film to take up the slack Open the printer door and insert the cassette Open the card tray Setting cards Inserting cards Unit can take about 300 0.76mm-thick cards Card bracket locks when it reaches the holePull the card bracket back Close the card tray When using contact IC cards When using magnetic cards Loading cardsFor JIS II cards For ISO cards Remove the card thickness switching plate Switching the card thicknessMalfunction of the printer Remove the blue securing screw Names of parts on the operation Panel LCD operation display content Operation display LED contents LCD panel Operation Turning on the power About the Reset button Turning off the powerTurn off the printer’s power Initialized without winding up. Default User modes User mode screen flow Main menu Submenu User mode settings Display mode settings Press Enter to reset Cleaning modeExit user mode Clearing the free counter Ink mode setting Set the retransfer temperature Retransfer mode settingSet retransfer film Set the retransfer speed Buzzer mode setting Setting the bend remedy mode Antimagnetic setting mode Card size setting modeTransport mode Test print Cleaning the cleaning rollers Care and cleaningRemove the cleaning unit Wipe the head indicated with horizontally Cleaning the thermal head How to attach the sponge Cleaning the fan filter on the back side Set a cleaning card Cleaning the card feed rollersFrom user mode select cleaning mode Turn off the power after the cleaning card is discharged Once printer servicing and cleaning Have been completed Cleaning the card feed rollers Heat rollersApply alcohol on the magnetic head cleaning card Set the card on the card tray Cleaning rollers TroubleshootingLayout of rollers inside the printer Card turnover table Meaning of reset → enter buttons in the list is Error code listing Troubleshooting Mending broken ink ribbon Retransfer film About printing errors Return the card tray to its original position Removing card jamsPush the card tray back into position on an angle Jog lever are supplied as standard Remove any jammed cardsTurn the jog dial Remove the card Main specifications Specifications Front view External appearance and dimensionsUnit/mm Ultra Electronics Card Systems