|
| LOW AIR |
|
| LOW AIR |
|
|
|
| PRESSURE |
|
| PRESSURE | WATER |
|
|
| SUPERVISORY | VALVE |
| ALARM | FLOW | MANUAL |
|
| SWITCH | TAMPER CONVENTIONAL SWITCH | SWITCH | RELEASE | ||
|
| 09473 SUPERVISORY DETECTION | 09473 | 09470 | STATION | ||
|
| EOLR | EOLR | EOLR | EOLR | EOLR | EOLR |
|
| 5.1K | 5.1K | 5.1K | 5.1K | 5.1K | 5.1K |
HOT - BLACK |
|
|
|
|
|
| ZONE 1 |
|
|
|
|
|
|
| |
NEUTRAL - WHITE |
|
|
|
|
|
|
|
| 120 OHM |
|
|
|
|
|
|
EARTH GROUND - GREEN |
|
|
|
|
|
|
|
N L |
|
|
|
|
|
|
|
24 VNR DC | AUX. POWER SUP 1 | SUP 2 | ZONE 1 | ZONE 2 | ZONE 3 | ZONE 4 | |
|
| 24VR DC |
|
|
|
|
|
| ZONE 1 | OUTPUT 1 |
| V F R |
|
|
| ||
| ZONE 2 | OUTPUT 2 |
|
|
| ZONE 3 | OUTPUT 3 |
|
|
|
|
| PROGRAM | RUN |
| ZONE 4 | OUTPUT 4 | MODE | MODE |
| AC POWER | SUPERVISORY 1 |
| |
| POWER TBL | SUPERVISORY 2 |
| BUZZER SILENCE |
|
|
| ||
RUN | SYSTEM TBL | COMMON ALARM |
|
|
SUP TBL | ALARM SILENCE |
| LAMP TEST | |
|
| |||
PROGRAM | GROUND | STEADY: DISCHARGED | SET | |
| PRE- | |||
| FAULT | FLASHING: DISCHARGE |
| }BUZZER SILENCE |
|
|
| SELECT | SIGNAL SILENCE |
|
|
| FUNCTION | SYSTEM RESET |
| VIEWING ANGLE |
|
|
|
TROUBLE | ALARM | SUPV | WTRFLW |
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 | COM NO NC | COM NO | COM NO |
COM NO NC |
BAT+ BAT-
RED | BLACK |
BLACK | RED | BLACK | RED | BLACK | RED | BLACK |
| RED |
|
|
|
|
|
|
|
| RELAY CONTACTS |
| 5.1K |
| 5.1K | EOL |
| 5.1K | DRY CONTACTS RATED AT 3A, 30VDC | |
| EOLR |
| EOLR | DIODE |
| EOLR |
| |
|
|
|
| ASSY |
|
|
|
GENERAL WATERFLOW | RELEASE SUPERVISORY | |
ALARM | SOLENOID | BELL |
DWG# 14166 VKG PRGM3
1.Run field wiring and ensure connections are proper by metering wires. Resistance reading should be 5.1K ohms with
2.Connect one circuit at a time and apply AC power.
3.Connect batteries to the panel.
4.Once last connection is made, move Program switch down.
5.Press the FUNCTION (bottom) button until the display reads “PASSWORD = 000”.
6.To enter a password, press the SELECT button until the proper number is displayed above the ^ symbol, then press the SET button to move to the next digit. After entering the third number the display will change. (All panels are shipped with a 000 password.)
7.Press the FUNCTION (bottom) button until the display reads “PROGRAM #3”.
8.Press the SELECT button until the display reads “PROGRAM #3”.
9.Press the SET button.
10.The panel is completely programmed except for the custom banner and zone messages. Move the program switch back up.
25