Manuals / Western Telematic / Computer Equipment / Switch

Western Telematic CMS-16 manual Free Any Undefined Enter /H for Command Menu

Models: CMS-16

1 59

Download 59 pages 31.71 Kb

Page 12

WTI CMS-16; Console Management Switch -- User's Guide				Free	Any		0
11	(undefined)	(undefined)		Free	Any		0
12	(undefined)	(undefined)		Free	Any		0
13	(undefined)	(undefined)		Free	Any		0
14	(undefined)	(undefined)		Free	Any		0
15	(undefined)	(undefined)		Free	Any		0
16	(undefined)	(undefined)		Free	Any		0

Enter /H for Command Menu

Figure 3.2: The Port Status Screen (Defaults Shown)

6.Port Connection: The CMS can perform two different types of port connections; Resident Connections and Third Party Connections.

. Resident Connection: Your resident port (e.g. Port 1) issues a /C command to connect to a second port.

i.To connect Port 1 to Port 2, type /C 2 [Enter]. While Port 1 is connected, the CMS will not recognize commands issued at Port 1. However, the unit will recognize a Resident Disconnect Sequence issued at Port 1 or Port 2.

ii.Issue the Resident Disconnect Sequence (Logoff Sequence); type [Enter]+++[Enter].

b.Third Party Connection: Your resident port (e.g. Port 1) issues a /C command to create a connection between two other ports.

i.To connect Port 2 to Port 3, type /C 2 3 [Enter].

ii.While Ports 2 and 3 are connected, Port 1 will still recognize CMS commands. Type /S [Enter] to display the Port Status Screen. The "STATUS" column should now list Ports 2 and 3 as connected, and Port 1 as "Free".

iii.Issue a Third Party Disconnect command to disconnect Ports 2 and 3; type /D 2 [Enter]. The unit will display the "Are you Sure (y/n)?" prompt. Type y and press [Enter] to disconnect.

iv.Type /S [Enter] to display the Port Status Screen. The "STATUS" column should now list Ports 2 and 3 as "Free".

7.Site I.D. Message: If desired, the Site I.D. Message can be used to indicate the name or location of the unit. Note that the Site I.D. cannot include double quotes (").

. Type /F and press [Enter]. When the System Parameters menu appears, type 1 and press [Enter]. A prompt will appear. Key in the desired text (up to 32 characters)

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (12 of 59) [11/15/2000 10:52:02 AM]

Image 12

Western Telematic CMS-16 manual Free Any Undefined Enter /H for Command Menu

Contents

CMS-16 Nameplate Power Warning Battery ReplacementRack Mount Installation Table of Contents WTI CMS-16 Console Management Switch -- Users Guide Appendices List of Figures Introduction Typographic Conventions Unit Description Front PanelBold Font Power Cable Receptacle Power Switch Getting StartedBack Panel Apply Power to the CMS System SetUp PortsUsing Other Parameters for this Overview Optional Communication Parameters Connecting your PC to the CMS Communicating with the CMS Unit Display Free Any Undefined Enter /H for Command Menu Hardware Installation Connecting Power to the CMS UnitAC Powered Units DC Powered Units Configure Option Switches Default Baud Rate Sw1, Sw2, Sw3 Default Handshake Sw4, Sw5 Default Response Message Format Sw6Default Command Echo Sw7 Initialize Unit to Default Settings Connecting Devices to the CMSApplication Example CMS Application Example Not to Scale Configuration Access to the CMS Command Mode Password Functions $ telnet 192.1.1.1 Enter Supervisor Password Port Passwords Defining the Site ID and Supervisor Password Port Configuration Configuration Conventions 3. RS232 Port Configuration Menus Port Modes Stop Bits Default = CTS/RTS AT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Network Port Configuration Menu Telnet Port Parameters Network Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Status Screens Save User Selected ParametersPort Status Screen /S Port Diagnostics Screen /SD Port Status Screen Supervisor Mode, Defaults Shown Port Name Status Baud COM HS Mode BUF CTS Network Status Screen /SN Port Parameters Screens /W WP xx Enter Any-to-Any Mode OperationPort Connection and Disconnection Disconnecting Ports Enter Defining Hunt Groups Hunt Group Example Passive Mode Buffer Mode Reading Data from Buffer Mode Ports Xx EnterPort Buffers Saving and Restoring Configuration Parameters Modem Mode Sending Parameters to a File Restoring Saved Parameters Upgrading CMS Firmware Command Reference Guide Command Conventions Command Response Terse Verbose Command Summary Command Availability Supervisor User Command Set Enter Enter Command Mode Enter+++Enter Resident Disconnect Sequence Connect CP Copy RS232 Port Parameters Third Party DisconnectErase Buffer Default and Test Set System ParametersHelp Display Site ID Set Network Port ParametersSet RS232 Port Parameters SD Display Port Diagnostics Reset Network PortDisplay Port Status SN Display Network Status UF Upgrade Firmware Save ParametersDisplay Port Parameters Who Exit Command Mode Appendix A. RS232 Port InterfaceFormat /X Enter Appendix B. Specifications Appendix C. Customer ServicePower Stop Bits 1 or Trademark and Copyright Information Trademarks Used in this Manual