CP Copy RS232 Port Parameters | Western Telematic CMS-16 specification

WTI CMS-16; Console Management Switch -- User's Guide

Verbose: Connected xx, when a Resident Connection is initiated, the CMS will also display the currently selected Resident Disconnect Sequence for your port.

Terse: 1

/CP Copy RS232 Port Parameters

Allows quick set-up when all CMS RS232 ports will be configured with the same or similar parameters. When the /CP command is invoked, the CMS will display a menu that is used to select common port parameters, which can then be copied to all CMS RS232 ports. For more information, please refer to Section 5.6.

Availability: Supervisor Only

Format: /CP [Enter]

Response: Displays Copy Parameters Menu

/D Third Party Disconnect

Invoke the /D command at your resident port to disconnect two other ports. The /D command cannot be used to disconnect your resident port. To disconnect your resident port, issue the Resident Disconnect Sequence or wait for the Timeout Period to elapse (if enabled).

Availability: Supervisor Only

Format: /D[/Y] <x> [x] [Enter]

Where:

/Y (Optional) suppresses the "Sure?" prompt.

xIs the number or name of the port(s) to be disconnected. To Disconnect all ports, enter an asterisk. To disconnect the Network Port, enter an "N".

Response:

Verbose: "Are you Sure (y/n)?", if Y, unit will respond with "Disconnected".

Terse: 5, if Y, unit will respond with 3.

Example: To disconnect Port 2 from Port 3 without the "Sure?" prompt, access the Command Mode from a third port with "All" command capability and type one of the following commands:

/D/Y 2 [Enter] or /D/Y 3 [Enter]

/E Erase Buffer

Erases data from the buffer for a specified port or several ports. Note that erased data cannot be

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (52 of 59) [11/15/2000 10:52:03 AM]

Image 52

Western Telematic CMS-16 manual CP Copy RS232 Port Parameters, Third Party Disconnect, Erase Buffer

Contents

CMS-16 Battery Replacement Nameplate Power WarningRack Mount Installation Table of Contents WTI CMS-16 Console Management Switch -- Users Guide Appendices List of Figures Introduction Typographic Conventions Front Panel Unit DescriptionBold Font Getting Started Power Cable Receptacle Power SwitchBack Panel Apply Power to the CMS System SetUp PortsUsing Other Parameters for this Overview Optional Communication Parameters Connecting your PC to the CMS Communicating with the CMS Unit Display Free Any Undefined Enter /H for Command Menu Hardware Installation Connecting Power to the CMS UnitAC Powered Units DC Powered Units Configure Option Switches Default Baud Rate Sw1, Sw2, Sw3 Default Response Message Format Sw6 Default Handshake Sw4, Sw5Default Command Echo Sw7 Connecting Devices to the CMS Initialize Unit to Default SettingsApplication Example CMS Application Example Not to Scale Configuration Access to the CMS Command Mode Password Functions $ telnet 192.1.1.1 Enter Supervisor Password Port Passwords Defining the Site ID and Supervisor Password Port Configuration Configuration Conventions 3. RS232 Port Configuration Menus Port Modes Stop Bits Default = CTS/RTS AT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Network Port Configuration Menu Telnet Port Parameters Network Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Save User Selected Parameters Status ScreensPort Status Screen /S Port Diagnostics Screen /SD Port Status Screen Supervisor Mode, Defaults Shown Port Name Status Baud COM HS Mode BUF CTS Network Status Screen /SN Port Parameters Screens /W WP xx Enter Operation Any-to-Any ModePort Connection and Disconnection Disconnecting Ports Enter Defining Hunt Groups Hunt Group Example Passive Mode Buffer Mode Xx Enter Reading Data from Buffer Mode PortsPort Buffers Saving and Restoring Configuration Parameters Modem Mode Sending Parameters to a File Restoring Saved Parameters Upgrading CMS Firmware Command Reference Guide Command Conventions Command Response Terse Verbose Command Summary Command Availability Supervisor User Command Set Enter Enter Command Mode Enter+++Enter Resident Disconnect Sequence Connect Third Party Disconnect CP Copy RS232 Port ParametersErase Buffer Set System Parameters Default and TestHelp Set Network Port Parameters Display Site IDSet RS232 Port Parameters SD Display Port Diagnostics Reset Network PortDisplay Port Status SN Display Network Status Save Parameters UF Upgrade FirmwareDisplay Port Parameters Who Appendix A. RS232 Port Interface Exit Command ModeFormat /X Enter Appendix B. Specifications Appendix C. Customer ServicePower Stop Bits 1 or Trademark and Copyright Information Trademarks Used in this Manual