AT&C1$D2S0=1 | Western Telematic CMS-16 manual

WTI CMS-16; Console Management Switch -- User's Guide

●7. Port Mode: Defines the operation mode for this port. Note that Ports 1 and 2 cannot be configured for Passive Mode or Buffer Mode. (Default = Any-to-Any Mode).

When Any-to-Any, Passive, or Buffer Mode is selected, the unit will display the DTR Output prompt as shown in Figure 5.1. The DTR Output prompt is not displayed when Modem Mode is selected.

❍74. DTR Output: Determines how the DTR line will react when this port disconnects. The DTR line can be held low, held high, or pulsed for 0.5 seconds and then held high. In the default state, the DTR line will pulse for 0.5 seconds and then remain high. For more information on DCD and DTR hardware lines, please refer to Appendix A. (Default = Pulse).

1.	Port Name:		(undefined)
2.	Password:		(undefined)
3.	Baud Rate:		9600
4.	Bits/Parity:		8-None
5.	Stop Bits:		1
6.	Handshake Mode:		CTS/RTS
7.	Port Mode:		Modem
	71.	Reset String:	ATZ
	72.	Init String:	AT&C1&D2S0=1
8.	73.	Hang-Up String:	(undefined)
8.	Supervisor Mode:		Permit
9.	Logoff Character:		+
10.	Sequence Disconnect:		Three Characters
11.	Timeout Disconnect:		Off
12.	Response Type:		Verbose
13.	Command Echo:		On
14.	Accept Break:		Yes

Enter: "<" Previous Port,

">" Next Port,

<ESC> Exit ...

Figure 5.2: Port Configuration Menu (Modem Mode)

When Port Mode (menu Item 7) is set to Modem Mode, the menu will include additional prompts (see Figure 5.2), which are used to define the following:

❍71. Reset String: If necessary, this prompt can be used to re-define the modem

reset string. The Reset String is sent prior to the Initialization string in order to select common initial parameters. (Default = ATZ).

❍72. Initialization String: Defines a command string that is sent after the Reset

String to initialize a modem to settings required by your application. (Default =

AT&C1$D2S0=1).

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (25 of 59) [11/15/2000 10:52:02 AM]

Image 25

Western Telematic CMS-16 manual AT&C1$D2S0=1

Contents

CMS-16 Battery Replacement Nameplate Power WarningRack Mount Installation Table of Contents WTI CMS-16 Console Management Switch -- Users Guide List of Figures Appendices Typographic Conventions Introduction Front Panel Unit DescriptionBold Font Getting Started Power Cable Receptacle Power SwitchBack Panel System SetUp Ports Apply Power to the CMSUsing Other Parameters for this Overview Optional Communication Parameters Communicating with the CMS Unit Connecting your PC to the CMS Display Free Any Undefined Enter /H for Command Menu Connecting Power to the CMS Unit Hardware InstallationAC Powered Units DC Powered Units Default Baud Rate Sw1, Sw2, Sw3 Configure Option Switches Default Response Message Format Sw6 Default Handshake Sw4, Sw5Default Command Echo Sw7 Connecting Devices to the CMS Initialize Unit to Default SettingsApplication Example CMS Application Example Not to Scale Access to the CMS Command Mode Configuration $ telnet 192.1.1.1 Enter Password Functions Port Passwords Supervisor Password Defining the Site ID and Supervisor Password Configuration Conventions Port Configuration Port Modes 3. RS232 Port Configuration Menus CTS/RTS Stop Bits Default = AT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Telnet Port Parameters Network Port Configuration Menu Network Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Save User Selected Parameters Status ScreensPort Status Screen /S Port Status Screen Supervisor Mode, Defaults Shown Port Diagnostics Screen /SD Port Name Status Baud COM HS Mode BUF CTS Port Parameters Screens /W Network Status Screen /SN WP xx Enter Operation Any-to-Any ModePort Connection and Disconnection Disconnecting Ports Enter Hunt Group Example Defining Hunt Groups Buffer Mode Passive Mode Xx Enter Reading Data from Buffer Mode PortsPort Buffers Modem Mode Saving and Restoring Configuration Parameters Restoring Saved Parameters Sending Parameters to a File Upgrading CMS Firmware Command Conventions Command Reference Guide Terse Verbose Command Response Command Availability Supervisor User Command Summary Enter Enter Command Mode Command Set Connect Enter+++Enter Resident Disconnect Sequence Third Party Disconnect CP Copy RS232 Port ParametersErase Buffer Set System Parameters Default and TestHelp Set Network Port Parameters Display Site IDSet RS232 Port Parameters Reset Network Port SD Display Port DiagnosticsDisplay Port Status SN Display Network Status Save Parameters UF Upgrade FirmwareDisplay Port Parameters Who Appendix A. RS232 Port Interface Exit Command ModeFormat /X Enter Appendix C. Customer Service Appendix B. SpecificationsPower Stop Bits 1 or Trademarks Used in this Manual Trademark and Copyright Information