Default Handshake Sw4, Sw5 | Western Telematic CMS-16 manual

WTI CMS-16; Console Management Switch -- User's Guide

Up Down Up 38.4K

Down Up Up 57.6K

Up Up Up 115.2K

*= Factory Setting

4.2.2.Default Handshake (Sw4, Sw5)

The default handshake format must match the format your control device will use when communicating with the CMS. Option Switches 4 and 5 can select RTS/CTS (hardware), XON/XOFF, Both or None.

Switch

Default Handshake

4 5

Down	Down RTS/CTS *

Up Down XON/XOFF

Down Up Both

Up Up None

*= Factory Setting

4.2.3.Default Response Message Format (Sw6)

When commands are invoked, the CMS can respond with either verbose (English text) or terse (numeric / abbreviated) messages. Response messages are summarized in Section 10.2. After installation, the /P command can also set the response format to "none" (Quiet Mode). When Quiet Mode is selected, the unit will not send response messages.

Switch 6 Default Response Message Type

Down	Verbose (English Text) *
Up	Terse (abbreviated / numeric)

*= Factory Setting

4.2.4.Default Command Echo (Sw7)

Switch Seven enables or disables the Command Echo. When enabled, characters sent to the CMS will be echoed back to the control device.

Switch 7 Default Command Echo

Down Enable*

Up Disable

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (15 of 59) [11/15/2000 10:52:02 AM]

Image 15

Western Telematic CMS-16 manual Default Handshake Sw4, Sw5, Default Response Message Format Sw6, Default Command Echo Sw7

Contents

CMS-16 Nameplate Power Warning Battery ReplacementRack Mount Installation Table of Contents WTI CMS-16 Console Management Switch -- Users Guide List of Figures Appendices Typographic Conventions Introduction Unit Description Front PanelBold Font Power Cable Receptacle Power Switch Getting StartedBack Panel Communication Parameters Apply Power to the CMSSystem SetUp Ports Using Other Parameters for this Overview Optional Communicating with the CMS Unit Connecting your PC to the CMS Display Free Any Undefined Enter /H for Command Menu DC Powered Units Hardware InstallationConnecting Power to the CMS Unit AC Powered Units Default Baud Rate Sw1, Sw2, Sw3 Configure Option Switches Default Handshake Sw4, Sw5 Default Response Message Format Sw6Default Command Echo Sw7 Initialize Unit to Default Settings Connecting Devices to the CMSApplication Example CMS Application Example Not to Scale Access to the CMS Command Mode Configuration $ telnet 192.1.1.1 Enter Password Functions Port Passwords Supervisor Password Defining the Site ID and Supervisor Password Configuration Conventions Port Configuration Port Modes 3. RS232 Port Configuration Menus CTS/RTS Stop Bits Default = AT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Telnet Port Parameters Network Port Configuration Menu Network Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Status Screens Save User Selected ParametersPort Status Screen /S Port Status Screen Supervisor Mode, Defaults Shown Port Diagnostics Screen /SD Port Name Status Baud COM HS Mode BUF CTS Port Parameters Screens /W Network Status Screen /SN WP xx Enter Any-to-Any Mode OperationPort Connection and Disconnection Disconnecting Ports Enter Hunt Group Example Defining Hunt Groups Buffer Mode Passive Mode Reading Data from Buffer Mode Ports Xx EnterPort Buffers Modem Mode Saving and Restoring Configuration Parameters Restoring Saved Parameters Sending Parameters to a File Upgrading CMS Firmware Command Conventions Command Reference Guide Terse Verbose Command Response Command Availability Supervisor User Command Summary Enter Enter Command Mode Command Set Connect Enter+++Enter Resident Disconnect Sequence CP Copy RS232 Port Parameters Third Party DisconnectErase Buffer Default and Test Set System ParametersHelp Display Site ID Set Network Port ParametersSet RS232 Port Parameters SN Display Network Status SD Display Port DiagnosticsReset Network Port Display Port Status UF Upgrade Firmware Save ParametersDisplay Port Parameters Who Exit Command Mode Appendix A. RS232 Port InterfaceFormat /X Enter Stop Bits 1 or Appendix B. SpecificationsAppendix C. Customer Service Power Trademarks Used in this Manual Trademark and Copyright Information