Connect | Western Telematic CMS-16 instruction

WTI CMS-16; Console Management Switch -- User's Guide

[Enter]+++[Enter] Resident Disconnect Sequence

The Resident Disconnect Sequence is issued to disconnect your resident port from another port. For example, if you are communicating via Port 3, and Port 3 is connected to Port 4, the Resident Disconnect Sequence would be used to disconnect Port 3 from Port 4. Although the default Resident Disconnect Sequence is [Enter]+++[Enter], the command format and Logoff Character can also be redefined via the Port Configuration Menus as described in Section 5.5.3. Note that a one character disconnect command can also be selected.

Availability: Supervisor / User

Format: [Enter]xxx[Enter]

Where "x" is the selected Logoff Character, and the default character is "+".

Response:

Verbose: The CMS will send the "Disconnected" message, followed by the Port Status Screen.

Terse: 3

/C Connect

Establishes a bi-directional connection between two ports. For more information and command line examples, please refer to Section 7.1. There are two different types of port connections:

●Resident Connect: If the /C command specifies one port name or number, your resident port will be connected to the specified port.

●Third Party Connect: If the /C command specifies two port names or numbers, the unit will connect the two ports indicated. A Third Party Connect command must be issued from a third port with "Supervisor" command capability. "User" ports cannot initiate a Third Party Connect.

Note:

●Ports with "User" command capability can only connect to ports that share the same Port Password.

●Ports with "Supervisor" command capability are allowed to connect to all other ports.

Availability: Supervisor / User

Format: /C <x> [x] [Enter]

Where x is the number or name of the port(s) to be connected.

Response:

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (51 of 59) [11/15/2000 10:52:03 AM]

Image 51

Western Telematic CMS-16 manual Enter+++Enter Resident Disconnect Sequence, Connect

Contents

CMS-16 Nameplate Power Warning Battery ReplacementRack Mount Installation Table of Contents WTI CMS-16 Console Management Switch -- Users Guide List of Figures Appendices Typographic Conventions Introduction Unit Description Front PanelBold Font Power Cable Receptacle Power Switch Getting StartedBack Panel Communication Parameters Apply Power to the CMSSystem SetUp Ports Using Other Parameters for this Overview Optional Communicating with the CMS Unit Connecting your PC to the CMS Display Free Any Undefined Enter /H for Command Menu DC Powered Units Hardware InstallationConnecting Power to the CMS Unit AC Powered Units Default Baud Rate Sw1, Sw2, Sw3 Configure Option Switches Default Handshake Sw4, Sw5 Default Response Message Format Sw6Default Command Echo Sw7 Initialize Unit to Default Settings Connecting Devices to the CMSApplication Example CMS Application Example Not to Scale Access to the CMS Command Mode Configuration $ telnet 192.1.1.1 Enter Password Functions Port Passwords Supervisor Password Defining the Site ID and Supervisor Password Configuration Conventions Port Configuration Port Modes 3. RS232 Port Configuration Menus CTS/RTS Stop Bits Default = AT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Telnet Port Parameters Network Port Configuration Menu Network Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Status Screens Save User Selected ParametersPort Status Screen /S Port Status Screen Supervisor Mode, Defaults Shown Port Diagnostics Screen /SD Port Name Status Baud COM HS Mode BUF CTS Port Parameters Screens /W Network Status Screen /SN WP xx Enter Any-to-Any Mode OperationPort Connection and Disconnection Disconnecting Ports Enter Hunt Group Example Defining Hunt Groups Buffer Mode Passive Mode Reading Data from Buffer Mode Ports Xx EnterPort Buffers Modem Mode Saving and Restoring Configuration Parameters Restoring Saved Parameters Sending Parameters to a File Upgrading CMS Firmware Command Conventions Command Reference Guide Terse Verbose Command Response Command Availability Supervisor User Command Summary Enter Enter Command Mode Command Set Connect Enter+++Enter Resident Disconnect Sequence CP Copy RS232 Port Parameters Third Party DisconnectErase Buffer Default and Test Set System ParametersHelp Display Site ID Set Network Port ParametersSet RS232 Port Parameters SN Display Network Status SD Display Port DiagnosticsReset Network Port Display Port Status UF Upgrade Firmware Save ParametersDisplay Port Parameters Who Exit Command Mode Appendix A. RS232 Port InterfaceFormat /X Enter Stop Bits 1 or Appendix B. SpecificationsAppendix C. Customer Service Power Trademarks Used in this Manual Trademark and Copyright Information