Command Summary | Western Telematic CMS-16 guide

WTI CMS-16; Console Management Switch -- User's Guide

7Invalid Syntax

8Invalid Access

9Enter Site ID: A Aborted

B Enter Password: C Invalid Password

D RAM Test Failed at *

E Inactivity Timeout, Disconnected

FData in Buffer from Previous Connection ...

Re-Enter Logoff Sequence to Purge Buffer.

GAsleep

*These verbose Response Messages include additional information not provided by terse Response Messages.

10.3. Command Summary

Function			Command Syntax

Enter Command Mode			[Enter]
Exit Command Mode			/X [Enter]
Help Menu			/H [Enter]
Display Site ID			/J [Enter]
Display Port Status			/S[P] [Enter]
Display Port Diagnostics			/SD [Enter]
Display Network Status			/SN [Enter]
Display Port			/W[P] [n] [Enter]
Parameters (Who)			/W[P] [n] [Enter]
Set System Parameters			/F [Enter]
Set Network Port Parameters			/N [Enter]
Set RS232 Port			/P <x> [Enter]
Parameters			/P <x> [Enter]
Copy RS232 Port Parameters			/CP [Enter]
Connect			/C <x> [x] [Enter]
Resident	(5)		[Enter]+++[Enter]
Disconnect	(5)		[Enter]+++[Enter]
Third Party	(6)		/D[/Y] <x> [x] [Enter]
Disconnect	(6)		/D[/Y] * [Enter]

Command Availability

Supervisor User

X X

X X

X X

X X

X (1) (2)		X (1)
X	(1)	X	(1)
	X
X	(2)	X	(3)

X

X

X

X

XX (4)

X X

X

file:///C/WEBPAGE/guides/cms/html/rev_b/Cmsguide.htm (49 of 59) [11/15/2000 10:52:03 AM]

Image 49

Western Telematic CMS-16 manual Command Summary, Command Availability Supervisor User

Contents

CMS-16 Battery Replacement Nameplate Power WarningRack Mount Installation Table of Contents WTI CMS-16 Console Management Switch -- Users Guide List of Figures Appendices Typographic Conventions Introduction Front Panel Unit DescriptionBold Font Getting Started Power Cable Receptacle Power SwitchBack Panel System SetUp Ports Apply Power to the CMSUsing Other Parameters for this Overview Optional Communication Parameters Communicating with the CMS Unit Connecting your PC to the CMS Display Free Any Undefined Enter /H for Command Menu Connecting Power to the CMS Unit Hardware InstallationAC Powered Units DC Powered Units Default Baud Rate Sw1, Sw2, Sw3 Configure Option Switches Default Response Message Format Sw6 Default Handshake Sw4, Sw5Default Command Echo Sw7 Connecting Devices to the CMS Initialize Unit to Default SettingsApplication Example CMS Application Example Not to Scale Access to the CMS Command Mode Configuration $ telnet 192.1.1.1 Enter Password Functions Port Passwords Supervisor Password Defining the Site ID and Supervisor Password Configuration Conventions Port Configuration Port Modes 3. RS232 Port Configuration Menus CTS/RTS Stop Bits Default = AT&C1$D2S0=1 WTI CMS-16 Console Management Switch -- Users Guide Telnet Port Parameters Network Port Configuration Menu Network Parameters Menu Supervisor Mode Only Implementing IP Security Security menu Figure Copying Parameters to All Ports Copy Port Parameters Menu Save User Selected Parameters Status ScreensPort Status Screen /S Port Status Screen Supervisor Mode, Defaults Shown Port Diagnostics Screen /SD Port Name Status Baud COM HS Mode BUF CTS Port Parameters Screens /W Network Status Screen /SN WP xx Enter Operation Any-to-Any ModePort Connection and Disconnection Disconnecting Ports Enter Hunt Group Example Defining Hunt Groups Buffer Mode Passive Mode Xx Enter Reading Data from Buffer Mode PortsPort Buffers Modem Mode Saving and Restoring Configuration Parameters Restoring Saved Parameters Sending Parameters to a File Upgrading CMS Firmware Command Conventions Command Reference Guide Terse Verbose Command Response Command Availability Supervisor User Command Summary Enter Enter Command Mode Command Set Connect Enter+++Enter Resident Disconnect Sequence Third Party Disconnect CP Copy RS232 Port ParametersErase Buffer Set System Parameters Default and TestHelp Set Network Port Parameters Display Site IDSet RS232 Port Parameters Reset Network Port SD Display Port DiagnosticsDisplay Port Status SN Display Network Status Save Parameters UF Upgrade FirmwareDisplay Port Parameters Who Appendix A. RS232 Port Interface Exit Command ModeFormat /X Enter Appendix C. Customer Service Appendix B. SpecificationsPower Stop Bits 1 or Trademarks Used in this Manual Trademark and Copyright Information