Manuals / Brands / Power Tools / Battery Charger / Xantrex Technology / Power Tools / Battery Charger

Xantrex Technology XC1524, XC2524, XC3012, XC5012 Symptom The XC S eries will not transition to equalization mode.

1 80

Download 80 pages, 1.23 Mb

Problem Solving

975-0187-01-01 4–9

SymptomThe XC Series appears to be taking too long to charge battery. Ready indicator light does not illuminate after 24 hours of charging.SymptomThe XC S eries will not transition to equalization mode.

Possible Cause Solution

Battery capacity is too high for the

XC Series model.

Load connected to battery is

draining charge current so that

battery does not recharge.

Battery has a damaged cell.

Use a higher capacity charger.

Disconnect load or switch load off.

Replace battery.

Possible Cause Solution

Battery is the wrong type, or set to

the wrong type to equalize.

Not all batteries are fully charged.

An active fault is present on the

bank you are attempting to equalize.

Verify battery type is set t o Gel or AGM. The se

battery types cannot be equalized.

Wait for all batteries to be in fl oat ( ) of 3-stage

charging or rest ( ) of 2-stage charging before

attempting to equalize (the ready indicator light will

illuminate).

Clear the active fault (see Table4-2 on page 4–4)

XC_Charger_Owner.book Page 9 Friday, August 12, 2005 3:23 PM

Contents

Main Page Page About Xantrex Trademarks Notice of Copyright Disclaimer Date and Revision About This Guide Purpose Scope Audience Organization Conventions Used Related Information Important Safety Instructions Explosive Gas and Battery Precautions WARNING: Explosion or fire hazard FCC Information Page Contents Important Safety Instructions 1 2 Introduction Page Page Xantrex XC3012, XC5012, XC1524 and XC2524 Battery Charger Features XC Series Appearance Information Centers of the XCSeries Remote Display Page Onboard Status Panel Figure 1-3 XC Series Onboard Status Panel Rear Panel Figure 1-4 XC Series Rear Panel Preparing for Installation Figure 1-5 XC Series System Tools and Materials Location Page Wiring Requirements DC Wiring Table 1-1 DC Wiring Requirements AC Wiring Battery Bank Size Requirements 2 Installing the XCSeries Installation Sequence WARNING: Shock and Energy Hazards Pre-Installing DC Wiring WARNING: Shock or arc burn hazard Pre-Installing AC Wiring Page Page Mounting the Remote Display Mounting Grounding WARNING: Electric shock hazard Final Connections Final DC Connections Final AC Connections Power ing Up Installing Optional Accessories Battery Temperature Sensor Drip Protection Rubber Boots Configuring the XCSeries Page Page About Charging Multiplex 3-Stage Charging Sequential 2-Stage Charg ing Charging Overview Page Page Charging Batteries Page Equalizing Flooded Batteries WARNING: Explosion hazard CAUTION: Risk of battery damage Page Transitioning the XCSeries to On, Disabled or Off Accessing Charger Information Reading Remote Display and Onboard Status Indicator Lights Table 3-1 Reading XCSeries Status Reporting While Charging or Equalizing Reporting While Battery Monitoring Reporting While Disabled Using A Generator As Source Power Page Page Care and Maintenance WARNING: Risk of electric shock Indicator Light Flashing Sequences Table 4-1 Indicator Light Sequences on the XCSeries Error Messages on Remote Display Page Page Problem Solving Page Symptom The XC S eries will not transition to equalization mode. Page Page Physical Specifications Electrical Specifications AC Input Specifications Temperature Specifications Protection Features Approvals Page 975-0187-01-01 WA1 Warranty and Product Information Limited Warranty for: What does this warranty cover and how long does it last? What will Xantrex do? How do you get ser vice? DISCLAIMER OF WARRANTY Exclusions 975-0187-01-01 WA3 WARNING: LIMITATIONS ON USE Return Material Authorization Policy Information About Your System Page Xantrex Technology Inc.