Manuals / Xerox / Computer Equipment / Printer

Xerox DocuPrint 96 manual Fuser agent, Put on gloves, Guide to Performing Routine Maintenance

Models: DocuPrint 96

1 60

Download 60 pages 56.39 Kb

Page 32

Fuser agent

Fuser agent

4. Put on gloves.

WARNING

Fuser agent contains silicone, which can cause irritation upon contact with the eyes. Be sure to wash your hands with soap and water after you finish this procedure.

5.Locate the fuser agent reservoir, pull it out until it stops, and remove the reservoir cap by turning it counterclockwise.

3-2	Guide to Performing Routine Maintenance

Image 32

Xerox DocuPrint 96 manual Fuser agent, Put on gloves, Guide to Performing Routine Maintenance

Contents

721P90060 Version 8.0 October Guide to Performing Routine MaintenanceXerox DocuPrint 96/4635/180/2000 Series NPS/IPS Guide to Performing Routine Maintenance Table of contents SafetyIntroduction 1. Feeder trays5. Replacing the dry ink waste container 6. Cleaning 7. Maintenance and support servicesSafety Laser safetyLABELS. ONLY XEROX SERVICE REPRESENTATIVES HAVE ACCESS TO THESE PANELSOperation safety U. S Ozone information U. S. onlyOperation safety Europe Warning markingsVentilation Operator accessible areasElectrical supply CE mark Europe only MaintenanceBefore cleaning your product Telecommunications Terminal Equipment Directive Radio and telecommunications equipment directive Europe onlyCertification to 1999/5/EC Radio Equipment and For further information SafetyGuide to Performing Routine Maintenance Europe+44 1707 USA1 800 Canada1 800Safety Guide to Performing Routine MaintenanceAbout this guide ContentsIntroduction Conventions Warnings alert you to conditions that may affect the safety of people Guide to Configuring and Managing the SystemGuide to Managing Print Jobs Guide to Performing Routine Maintenance Guide to Using Page Description Languages Installation Planning GuideIntroduction Submitting your Jobs from UNIX & DOS Quick Reference CardGuide to Performing Routine Maintenance 1. Feeder trays Checking feeder traysAdditional guidelines for loading special stocks Loading feeder traysGuidelines for loading paper Loading trays 1 and 3. Pull the feeder tray out until it stops Guide to Performing Routine MaintenanceFeeder trays Do not load above the MAX line shown on the paper guide Guide to Performing Routine MaintenanceFeeder trays 8. Pull the length guide forward to touch the back of the paper stackLoading trays 3, 4, 5, and 3. Pull the feeder tray out until it stops Feeder trays 2. Wait until the Ready to Open indicator lightsGuide to Performing Routine Maintenance 7. Slide both length guides back against the paper Guide to Performing Routine MaintenanceFeeder trays Guide to Performing Routine Maintenance Feeder trays1-10 Guide to Performing Routine MaintenanceFeeder trays Checking and unloading purge trays 2. Output trays and binsChecking and unloading the sample tray Checking and unloading high-capacity stacker HCS bins Unloading a stacker binAlways use both hands to lift the paper stack out of the bin Bin UnloadGuide to Performing Routine Maintenance Output trays and bins3. Fuser agent 4. Put on gloves Guide to Performing Routine MaintenanceFuser agent Guide to Performing Routine Maintenance Fuser agentPage NOTE The fuser agent message disappears after the printer prints between 32 and 40 sheets. Since the sheets must be processed continuously, you may want to run 45 test pages in order to clear the message from the system unless the current print job contains at least 40 pages Guide to Performing Routine Maintenance Fuser agent4. Adding dry ink Guide to Performing Routine Maintenance Adding dry ink2. Place a dropcloth on the floor under the dry ink area 3. Pull the empty dry ink cartridge out until it stops6. Insert the new cartridge into the printer until it stops Guide to Performing Routine MaintenanceAdding dry ink Remove the empty cartridge and discard it Page 5. Replacing the dry ink waste container To prevent dry ink spills, do not tip or tilt the waste container Guide to Performing Routine MaintenanceReplacing the dry ink waste container 3. Pull the full waste container out of the printerNOTE Do not remove the cap from the container Guide to Performing Routine Maintenance Replacing the dry ink waste container6. Cleaning Cleaning the sensors and the reflective surfaces Do not use any abrasives or strong solvents on the sensorCleaning the Q850 sensor CleaningTo clean the Q850 sensor Guide to Performing Routine Maintenance4. Lower the area 4 green handle 5. Close the printer doors CleaningGuide to Performing Routine Maintenance Cleaning the Q1011 sensor and mirror CleaningTo clean the Q1011 sensor and mirror 2. Apply a small amount of lens and mirror cleaner to a cleaning pad4. Close the printer doors CleaningGuide to Performing Routine Maintenance Cleaning additional sensors Sensor Q1107Guide to Performing Routine Maintenance Q1106 and Q1166Cleaning Cleaning the 4mm cartridge tape drive Sensor Q1164Page Xerox Documentation and Software Services 7. Maintenance and support servicesXerox Customer Service Center Xerox Font Center Operator trainingXerox Customer Education Reporting billing metersMaintenance and support services Guide to Performing Routine MaintenanceIndex Numerics