Manuals / Xerox / Computer Equipment / Printer

Xerox DocuPrint 96 manual NOTE Do not remove the cap from the container

Models: DocuPrint 96

1 60

Download 60 pages 56.39 Kb

Page 43

NOTE: Do not remove the cap from the container.

Replacing the dry ink waste container

5.Discard the waste material and container according to the instructions on the label.

6.Slide a new, empty dry ink waste container into the printer until it stops.

NOTE: Do not remove the cap from the container.

7.Close the printer doors.

8.Dispose of the dropcloth.

CAUTION

If any dry ink gets on your hands, wash them with soap and cold water. Heat sets the ink permanently. If any dry ink gets on your clothes, brush them with a dry paper towel or a stiff-bristled brush. If this does not remove the ink, launder with detergent and cold water. Tell dry cleaners that the spot is dry ink for a printer so they do not use a solvent that sets the stain.

Guide to Performing Routine Maintenance

5-3

Image 43

Xerox DocuPrint 96 manual NOTE Do not remove the cap from the container

Contents

Xerox DocuPrint 96/4635/180/2000 Series NPS/IPS Guide to Performing Routine Maintenance721P90060 Version 8.0 October Guide to Performing Routine Maintenance 1. Feeder trays Table of contentsSafety Introduction7. Maintenance and support services 5. Replacing the dry ink waste container 6. CleaningACCESS TO THESE PANELS SafetyLaser safety LABELS. ONLY XEROX SERVICE REPRESENTATIVES HAVEOzone information U. S. only Operation safety U. SWarning markings Operation safety EuropeElectrical supply Operator accessible areasVentilation Before cleaning your product MaintenanceCE mark Europe only Certification to 1999/5/EC Radio Equipment and Radio and telecommunications equipment directive Europe onlyTelecommunications Terminal Equipment Directive Europe+44 1707 USA1 800 Canada1 800 For further informationSafety Guide to Performing Routine MaintenanceGuide to Performing Routine Maintenance SafetyIntroduction ContentsAbout this guide Conventions Guide to Using Page Description Languages Installation Planning Guide Warnings alert you to conditions that may affect the safety of peopleGuide to Configuring and Managing the System Guide to Managing Print Jobs Guide to Performing Routine MaintenanceGuide to Performing Routine Maintenance Submitting your Jobs from UNIX & DOS Quick Reference CardIntroduction Checking feeder trays 1. Feeder traysGuidelines for loading paper Loading feeder traysAdditional guidelines for loading special stocks Loading trays 1 and Feeder trays Guide to Performing Routine Maintenance3. Pull the feeder tray out until it stops 8. Pull the length guide forward to touch the back of the paper stack Do not load above the MAX line shown on the paper guideGuide to Performing Routine Maintenance Feeder traysLoading trays 3, 4, 5, and Guide to Performing Routine Maintenance Feeder trays 2. Wait until the Ready to Open indicator lights3. Pull the feeder tray out until it stops Feeder trays Guide to Performing Routine Maintenance7. Slide both length guides back against the paper Feeder trays Guide to Performing Routine MaintenanceFeeder trays Guide to Performing Routine Maintenance1-10 Checking and unloading the sample tray 2. Output trays and binsChecking and unloading purge trays Unloading a stacker bin Checking and unloading high-capacity stacker HCS binsBin Unload Always use both hands to lift the paper stack out of the binOutput trays and bins Guide to Performing Routine Maintenance3. Fuser agent Fuser agent Guide to Performing Routine Maintenance4. Put on gloves Fuser agent Guide to Performing Routine MaintenancePage NOTE The fuser agent message disappears after the printer prints between 32 and 40 sheets. Since the sheets must be processed continuously, you may want to run 45 test pages in order to clear the message from the system unless the current print job contains at least 40 pages Fuser agent Guide to Performing Routine Maintenance4. Adding dry ink 3. Pull the empty dry ink cartridge out until it stops Guide to Performing Routine MaintenanceAdding dry ink 2. Place a dropcloth on the floor under the dry ink areaAdding dry ink Remove the empty cartridge and discard it Guide to Performing Routine Maintenance6. Insert the new cartridge into the printer until it stops Page 5. Replacing the dry ink waste container 3. Pull the full waste container out of the printer To prevent dry ink spills, do not tip or tilt the waste containerGuide to Performing Routine Maintenance Replacing the dry ink waste containerNOTE Do not remove the cap from the container Replacing the dry ink waste container Guide to Performing Routine Maintenance6. Cleaning Do not use any abrasives or strong solvents on the sensor Cleaning the sensors and the reflective surfacesGuide to Performing Routine Maintenance Cleaning the Q850 sensorCleaning To clean the Q850 sensorGuide to Performing Routine Maintenance Cleaning4. Lower the area 4 green handle 5. Close the printer doors 2. Apply a small amount of lens and mirror cleaner to a cleaning pad Cleaning the Q1011 sensor and mirrorCleaning To clean the Q1011 sensor and mirrorGuide to Performing Routine Maintenance Cleaning4. Close the printer doors Sensor Q1107 Cleaning additional sensorsCleaning Q1106 and Q1166Guide to Performing Routine Maintenance Sensor Q1164 Cleaning the 4mm cartridge tape drivePage Xerox Customer Service Center 7. Maintenance and support servicesXerox Documentation and Software Services Operator training Xerox Font CenterReporting billing meters Xerox Customer EducationGuide to Performing Routine Maintenance Maintenance and support servicesNumerics Index