Manuals / Xerox / Computer Equipment / Printer

Xerox DocuPrint 96 manual Cleaning the 4mm cartridge tape drive, Sensor Q1164

Models: DocuPrint 96

1 60

Download 60 pages 56.39 Kb

Page 53

Image 53

Cleaning

Sensor Q1164

Sensor Q1164 is on the last feeder/stacker module (the one containing the purge tray), as shown below. Clean the sensor gently, with a cleaning pad.

Cleaning the 4mm cartridge tape drive

Clean the 4mm cartridge tape drive every 25 hours of actual tape operation. Use only a cleaning cartridge designed for the 4mm cartridge tape drive. No fluids or other preparations are necessary with the use of these cartridges.

CAUTION

Do not use cleaning cartridges or any types of fluids designed for use in audio devices as these can damage your tape drive.

To clean the tape drive:

1.Insert the cleaning cartridge into the tape drive as you would a data tape cartridge.

Guide to Performing Routine Maintenance

6-9

Page 53

Image 53

Xerox DocuPrint 96 manual Cleaning the 4mm cartridge tape drive, Sensor Q1164

Contents

721P90060 Version 8.0 October Guide to Performing Routine MaintenanceXerox DocuPrint 96/4635/180/2000 Series NPS/IPS Guide to Performing Routine Maintenance Safety Table of contentsIntroduction 1. Feeder trays7. Maintenance and support services 5. Replacing the dry ink waste container 6. CleaningLaser safety SafetyLABELS. ONLY XEROX SERVICE REPRESENTATIVES HAVE ACCESS TO THESE PANELSOzone information U. S. only Operation safety U. SWarning markings Operation safety EuropeVentilation Operator accessible areasElectrical supply CE mark Europe only MaintenanceBefore cleaning your product Telecommunications Terminal Equipment Directive Radio and telecommunications equipment directive Europe onlyCertification to 1999/5/EC Radio Equipment and Safety For further informationGuide to Performing Routine Maintenance Europe+44 1707 USA1 800 Canada1 800Guide to Performing Routine Maintenance SafetyAbout this guide ContentsIntroduction Conventions Guide to Configuring and Managing the System Warnings alert you to conditions that may affect the safety of peopleGuide to Managing Print Jobs Guide to Performing Routine Maintenance Guide to Using Page Description Languages Installation Planning GuideIntroduction Submitting your Jobs from UNIX & DOS Quick Reference CardGuide to Performing Routine Maintenance Checking feeder trays 1. Feeder traysAdditional guidelines for loading special stocks Loading feeder traysGuidelines for loading paper Loading trays 1 and 3. Pull the feeder tray out until it stops Guide to Performing Routine MaintenanceFeeder trays Guide to Performing Routine Maintenance Do not load above the MAX line shown on the paper guideFeeder trays 8. Pull the length guide forward to touch the back of the paper stackLoading trays 3, 4, 5, and 3. Pull the feeder tray out until it stops Feeder trays 2. Wait until the Ready to Open indicator lightsGuide to Performing Routine Maintenance 7. Slide both length guides back against the paper Guide to Performing Routine MaintenanceFeeder trays Feeder trays Guide to Performing Routine Maintenance1-10 Guide to Performing Routine MaintenanceFeeder trays Checking and unloading purge trays 2. Output trays and binsChecking and unloading the sample tray Unloading a stacker bin Checking and unloading high-capacity stacker HCS binsBin Unload Always use both hands to lift the paper stack out of the binOutput trays and bins Guide to Performing Routine Maintenance3. Fuser agent 4. Put on gloves Guide to Performing Routine MaintenanceFuser agent Fuser agent Guide to Performing Routine MaintenancePage NOTE The fuser agent message disappears after the printer prints between 32 and 40 sheets. Since the sheets must be processed continuously, you may want to run 45 test pages in order to clear the message from the system unless the current print job contains at least 40 pages Fuser agent Guide to Performing Routine Maintenance4. Adding dry ink Adding dry ink Guide to Performing Routine Maintenance2. Place a dropcloth on the floor under the dry ink area 3. Pull the empty dry ink cartridge out until it stops6. Insert the new cartridge into the printer until it stops Guide to Performing Routine MaintenanceAdding dry ink Remove the empty cartridge and discard it Page 5. Replacing the dry ink waste container Guide to Performing Routine Maintenance To prevent dry ink spills, do not tip or tilt the waste containerReplacing the dry ink waste container 3. Pull the full waste container out of the printerNOTE Do not remove the cap from the container Replacing the dry ink waste container Guide to Performing Routine Maintenance6. Cleaning Do not use any abrasives or strong solvents on the sensor Cleaning the sensors and the reflective surfacesCleaning Cleaning the Q850 sensorTo clean the Q850 sensor Guide to Performing Routine Maintenance4. Lower the area 4 green handle 5. Close the printer doors CleaningGuide to Performing Routine Maintenance Cleaning Cleaning the Q1011 sensor and mirrorTo clean the Q1011 sensor and mirror 2. Apply a small amount of lens and mirror cleaner to a cleaning pad4. Close the printer doors CleaningGuide to Performing Routine Maintenance Sensor Q1107 Cleaning additional sensorsGuide to Performing Routine Maintenance Q1106 and Q1166Cleaning Sensor Q1164 Cleaning the 4mm cartridge tape drivePage Xerox Documentation and Software Services 7. Maintenance and support servicesXerox Customer Service Center Operator training Xerox Font CenterReporting billing meters Xerox Customer EducationGuide to Performing Routine Maintenance Maintenance and support servicesNumerics Index