Manuals / Xerox / Computer Equipment / Printer

Xerox DocuPrint 96 manual

Models: DocuPrint 96

1 60

Download 60 pages 56.39 Kb

Page 34

Manual background

Fuser agent

WARNING

If any fuser agent spills on the floor, remove it immediately. Fuser agent spills make the floor slippery. Use of Xerox Film Remover (isopropynal alcohol) is recommended to clean up spills.

CAUTION

The fuser reservoir has an anti-splash seal. Do not push the fuser agent bottle into the reservoir with excessive force, as this can damage the seal.

7.Replace the reservoir cap by turning it clockwise and push the fuser agent reservoir in until it stops.

8.Push the fuser drawer in until it latches in place.

3-4	Guide to Performing Routine Maintenance

Image 34

Xerox DocuPrint 96 manual

Contents

Xerox DocuPrint 96/4635/180/2000 Series NPS/IPS Guide to Performing Routine Maintenance721P90060 Version 8.0 October Guide to Performing Routine Maintenance Introduction Table of contentsSafety 1. Feeder trays5. Replacing the dry ink waste container 6. Cleaning 7. Maintenance and support servicesLABELS. ONLY XEROX SERVICE REPRESENTATIVES HAVE SafetyLaser safety ACCESS TO THESE PANELSOperation safety U. S Ozone information U. S. onlyOperation safety Europe Warning markingsElectrical supply Operator accessible areasVentilation Before cleaning your product MaintenanceCE mark Europe only Certification to 1999/5/EC Radio Equipment and Radio and telecommunications equipment directive Europe onlyTelecommunications Terminal Equipment Directive Guide to Performing Routine Maintenance For further informationSafety Europe+44 1707 USA1 800 Canada1 800Safety Guide to Performing Routine MaintenanceIntroduction ContentsAbout this guide Conventions Guide to Managing Print Jobs Guide to Performing Routine Maintenance Warnings alert you to conditions that may affect the safety of peopleGuide to Configuring and Managing the System Guide to Using Page Description Languages Installation Planning GuideGuide to Performing Routine Maintenance Submitting your Jobs from UNIX & DOS Quick Reference CardIntroduction 1. Feeder trays Checking feeder traysGuidelines for loading paper Loading feeder traysAdditional guidelines for loading special stocks Loading trays 1 and Feeder trays Guide to Performing Routine Maintenance3. Pull the feeder tray out until it stops Feeder trays Do not load above the MAX line shown on the paper guideGuide to Performing Routine Maintenance 8. Pull the length guide forward to touch the back of the paper stackLoading trays 3, 4, 5, and Guide to Performing Routine Maintenance Feeder trays 2. Wait until the Ready to Open indicator lights3. Pull the feeder tray out until it stops Feeder trays Guide to Performing Routine Maintenance7. Slide both length guides back against the paper Guide to Performing Routine Maintenance Feeder traysFeeder trays Guide to Performing Routine Maintenance1-10 Checking and unloading the sample tray 2. Output trays and binsChecking and unloading purge trays Checking and unloading high-capacity stacker HCS bins Unloading a stacker binAlways use both hands to lift the paper stack out of the bin Bin UnloadGuide to Performing Routine Maintenance Output trays and bins3. Fuser agent Fuser agent Guide to Performing Routine Maintenance4. Put on gloves Guide to Performing Routine Maintenance Fuser agentPage NOTE The fuser agent message disappears after the printer prints between 32 and 40 sheets. Since the sheets must be processed continuously, you may want to run 45 test pages in order to clear the message from the system unless the current print job contains at least 40 pages Guide to Performing Routine Maintenance Fuser agent4. Adding dry ink 2. Place a dropcloth on the floor under the dry ink area Guide to Performing Routine MaintenanceAdding dry ink 3. Pull the empty dry ink cartridge out until it stopsAdding dry ink Remove the empty cartridge and discard it Guide to Performing Routine Maintenance6. Insert the new cartridge into the printer until it stops Page 5. Replacing the dry ink waste container Replacing the dry ink waste container To prevent dry ink spills, do not tip or tilt the waste containerGuide to Performing Routine Maintenance 3. Pull the full waste container out of the printerNOTE Do not remove the cap from the container Guide to Performing Routine Maintenance Replacing the dry ink waste container6. Cleaning Cleaning the sensors and the reflective surfaces Do not use any abrasives or strong solvents on the sensorTo clean the Q850 sensor Cleaning the Q850 sensorCleaning Guide to Performing Routine MaintenanceGuide to Performing Routine Maintenance Cleaning4. Lower the area 4 green handle 5. Close the printer doors To clean the Q1011 sensor and mirror Cleaning the Q1011 sensor and mirrorCleaning 2. Apply a small amount of lens and mirror cleaner to a cleaning padGuide to Performing Routine Maintenance Cleaning4. Close the printer doors Cleaning additional sensors Sensor Q1107Cleaning Q1106 and Q1166Guide to Performing Routine Maintenance Cleaning the 4mm cartridge tape drive Sensor Q1164Page Xerox Customer Service Center 7. Maintenance and support servicesXerox Documentation and Software Services Xerox Font Center Operator trainingXerox Customer Education Reporting billing metersMaintenance and support services Guide to Performing Routine MaintenanceIndex Numerics