268890-UIM-B-0607

Horizontal Right Air Flow (Inducer High)

Refer to Figures 33-36

Installation with condensate trap bracket (Front of casing): Refer to Figure 33 & 34

1.Remove the 2" knockout on the casing side, away from the inducer motor.

2.Remove all the condensate hoses inside the furnace, including the 3/8" barbed nipple, factory installed, in the rain gutter.

3.Remove the drain cap from the bottom rain gutter drain and insert the 3/8” barbed nipple removed above in the bottom rain gutter drain. Place the cap, just removed, to the other side of the rain gut- ter on the inducer.

4.Remove the condensate trap and its bracket from inside the fur- nace, saving the screws for later use.

5.Remove the large condensate cap from the side of the condensate pan and install it on the middle drain of the condensate pan, from where #1 hose was removed.

6.Install longer dogleg end of hose #10 through the casing hole on to the side drain of the condensate pan, where cap was removed in step #3. Some lubricant may have to be used to facilitate this installation as the hose is designed to be a tight fit over the con- densate drain. The other, smaller, dogleg end of hose #10 should be installed into the large recessed drain in the condensate trap.

7.Install the condensate trap bracket, with the condensate trap, on to the front side of the furnace, using the screws removed in step #1.

8.Install the dogleg end of hose #9 on the Wye drain and route the hose through the opening on top of the furnace, as shown. Install the other end of the #9 hose to the barbed tee, inside the furnace.

9.Install the dogleg end of hose #4 to the rain gutter on the inducer. The other end of hose #4 should be installed on the 3/8" barbed tee.

10.Install one end of hose #7 on the 3/8" barbed tee inside the fur- nace. Guide the other end of hose #7 towards the condensate trap, and install it on the tap on the condensate trap.

11.Install the dogleg end of hose #2 on the bottom drain of the inducer. Guide the other end of hose #2 towards the condensate trap, and install it on the small recessed drain in the condensate trap.

12.Ensure that all hoses are properly installed, have no kinks, and are draining properly. All hoses on the condensate trap and conden- sate pan should be pushed all the way down to ensure against leakage and performance. Some hoses may have to be trimmed for proper fit.

NOTE: The condensate trap can also be installed on the 2" knockout opening, in this configuration, using the provided condensate trap bracket. Some modifications may, however, have to be made to the condensate hoses.

Ensure all condensate hoses are pushed all the way down on the condensate trap, barbed fittings, and condensate pan drains.

Plug all unused condensate trap, condensate pan and inducer drain connection points using plugs provided.

Installation with condensate trap bracket (Back of casing): Refer to Figure 35 & 36

1.Remove the 2" knockout on the casing side, away from the inducer motor.

2.Remove all the condensate hoses inside the furnace, including the 3/8" barbed nipple, factory installed, in the rain gutter.

3.Remove the drain cap from the bottom rain gutter drain and insert the 3/8” barbed nipple removed above in the bottom rain gutter drain. Place the cap, just removed, to the other side of the rain gut- ter on the inducer.

4.Remove the condensate trap and it's bracket from inside the fur- nace, saving the screws for later, use.

5.Remove the large condensate cap from the side of the condensate pan and install it on the middle drain of the condensate pan, from where #1 hose was removed.

6.Do not remove condensate trap from the condensate trap bracket.

7.Cut 2-1/2" straight piece from hose #1 and install it through the knockout opening in the casing on the side of the condensate pan, from where the cap was previously removed. Insert the other end of the hose into the large recessed drain on the condensate trap.

8.Install the condensate trap bracket to the 2” inch hole on the side of casing, using existing holes, lining up the condensate pan open- ing with the larger opening on the condensate trap.

9.Install the dogleg end of hose #9 on the Wye drain and route the hose through the opening on top of the furnace. Install the other end of the #9 hose to the barbed tee, inside the furnace.

10.Install the dogleg end of hose #4 on 3/8" barbed nipple, in the rain gutter. The other end of hose #4 should be installed on the 3/8" barbed tee.

11.Install one end of hose #7 on the 3/8" barbed tee inside the fur- nace. Guide the other end of hose #7 towards the condensate trap, and install it on the tap on the condensate trap

12.Install the dogleg end of hose #2 on the bottom drain of the inducer. Guide the other end of hose #2 towards the condensate trap, and install it on the small recessed drain in the condensate trap.

13.Ensure that all hoses are properly installed, have no kinks, and are draining properly. All hoses on the condensate trap should be pushed all the way down to ensure against leakage. All hoses on the condensate pan should be pulled all the way up to ensure proper operation.

26

Unitary Products Group

Page 25 Page 27
Page 26
Image 26
York GF9S*DH, GM9S*DH, GY9S*DH installation manual Horizontal Right Air Flow Inducer High Refer to Figures
Page 25 Page 27

GF9S*DH, GY9S*DH, GM9S*DH specifications

The York GM9S*DH, GF9S*DH, and GY9S*DH series air conditioning systems are known for their robust performance, reliability, and energy efficiency. These models are well-suited for both residential and light commercial applications, making them versatile options for a range of users.

One of the standout features of these systems is their high efficiency. The GM9S*DH is equipped with advanced heating and cooling technologies that allow it to achieve excellent SEER (Seasonal Energy Efficiency Ratio) ratings. This translates to lower energy consumption and reduced utility bills for homeowners and business operators alike. The GF9S*DH model further enhances this efficiency by incorporating variable-speed blowers that adjust airflow based on specific needs, ensuring that the system operates only as necessary.

Reliability is another key characteristic of the York GM9S*DH, GF9S*DH, and GY9S*DH series. These models are engineered with durable components and rigorous performance testing, which contributes to their long lifespan and minimizes the need for repairs. Moreover, they come with robust warranties that provide peace of mind for consumers.

In terms of technology, these units utilize a smart thermostat feature that allows for precise temperature control and programmable settings. This feature not only enhances comfort but also contributes to energy savings by allowing users to set optimal cooling or heating schedules. The systems are also designed with quiet operation in mind, employing sound-dampening features that minimize noise levels, which is particularly beneficial for residential installations.

The installation of the York GM9S*DH, GF9S*DH, and GY9S*DH systems is straightforward, offering flexibility in placement and integration with various home or office setups. Their compact design allows them to fit seamlessly into different environments without compromising on performance.

Additionally, the systems are equipped with advanced filtration options that improve indoor air quality by capturing allergens and pollutants. This is particularly beneficial for families with children or members who suffer from allergies.

Overall, the York GM9S*DH, GF9S*DH, and GY9S*DH series provide exceptional performance, energy efficiency, and reliability, making them an ideal choice for maintaining a comfortable indoor environment. With their cutting-edge technologies and user-friendly features, these systems represent an excellent investment for anyone looking to enhance their heating and cooling experience.
Top Page Image Contents