Connecting To The Computer | Zebra Technologies TTP 7030 instruction

16

Installation

Connecting To The Computer

Connecting To The Computer

Caution • Using a non-Zebra power supply may cause excessive EMC interferences and void the EMC certifications of the printer.

Connect the TTP 7030

1.Connect J13 of the printer to the USB port of the computer or the USB hub to be used. USB connectors can be recognized by the following symbol:

.

Note • Connector J13 is a 4-pin USB type B connector. See USB, TTP 7030 on page 877 for pin assignment.

Note • A suitable cable is available from Zebra, see Ordering numbers on page 115 for ordering number.

Figure 4 • USB Cable with Type A and Type B Connectors

Using a Serial Adapter

1.Loosen the control board module; see Removal on page 110.

2.Connect the serial adapter to J4 on the control board.

3.Fasten the control board module; see Removal on page 110.

4.Fasten the serial adapter with the two screws on the right hand side of the printer.

5.Connect a Zebra serial cable, ordering No.10825-000, between the printer and the computer to be used.

Important • We strongly recommend using the Zebra cable because many incompatible cables are available.

P1003636-002

TTP 7030™ Technical Manual

10/05/2009

Image 16

Zebra Technologies TTP 7030 technical manual Connecting To The Computer, Connect the TTP, Using a Serial Adapter

Contents

Zebra TTP P1003636-002 TTP 7030 Technical Manual 10/05/2009 Contents Programming Interface P1003636-002 TTP 7030 Technical Manual 10/05/2009 About This Manual IntroductionUpdating Contacts Mail address emb@zebra.com Subject line Emaillist Product Presentation Printer Exterior, Rear View Printer Exterior, Side View Status Indicator IndicatorsControl Board Indicators Feed Button Installation Installation Considerations Top view Electrostatic Discharges, and Earth Currents Ambient Light Using a Serial Adapter Connecting To The ComputerConnect the TTP Fitting a serial adapter to the printer Connecting the Power GND Is a power button available for the printer? Making a Test Printout Installing a Printer Driver Paper Level Sensor Indicators on Roll Holder Paper Level Sensors Paper-near-end Sensor Connection Operation Installing a Paper Roll Make sure the printer is turned on Angle Cut the paper in a suitable angle. See Figure Clearing Paper Jams Open the Print Module Programming Cursor will retain its last position on the ticket Text text How The Commands Are Described Two-Byte Character Definitions Therefore, the two-byte representation of 731 is Summary Of Control Codes & Escape Sequences 27 5 Head temperature Enquiry 27 5 Bootware version Enquiry50 n1 27 5 80 n1 Parameter-setting data Enquiry 27 5 Device ID Enquiry Software Command Syntax Black Mark Top-Of-Form Commands Changes the alignment of text and logotypes Text CommandsLeft Center Right Selects normal font font ESC ! 4 selects font Selects font ESC ! 5 selects fontSelects font Turns OFF Italics Normal Turns on Italics ESC T n1 Reversed/Inversed Text ESC w n1 Commands, are not cancelled Overprint the O ESC d n1 Make n Linefeeds Barcode Commands Samples of barcodes UPC Add-on. Two of five characters are allowed of the add-on Must be placed at the end of the bar code data Columns Error level, 0=auto, 1=Level0, 2=Level1, etcDot Height, sets mow many pixel lines each row consists Graphics Commands Determines the number of bytes. Range ESCr000000000000001193000024003 ESC g n1 Print Logotype Print Commands Form feed Clear presenterRun presenter Print buffer full Press on FF-button ESC j n1 Paper Reverse Cut And Present Commands You can also use RS together with the paper advance commandTo auto Gives a cut & eject after the last text line Ejects the presented Retracts the presented ENQ System Related Commands Erases all logotypes stored in the flash Prom Erases all fonts stored in the flash Prom See Default Parameter Settings on Set several parameters at once Status Reporting Commands Paper-near-end Enquiry Read← Sensor Status Read←n Where n can be ‘A’ Ascii or 41 hex or 65 dec That is, a response with the value 129 indicates version That is, a response with the value 130 indicates version Under Summary Of Parameter Settings on One-byte marker. Range 1h to 255h Font Loading File Format Character bitmap data Logotypes Loading All logotypes are erased with the ESC&L command Printing Status Reporting Default Parameter Settings Programming Default Parameter Settings Default Value Summary Of Parameter Settings Serial Interface Set-Up Select what handshaking to use on the serial interface No flow controlXon / Xoff Hardware No, paper out and error signals are not disabled Parallel Port SetupYes, paper out and error signals are disabled Print Setup Disable the loopCurrent consumption Cm loop Controls what the printer does with buffered data Burn pulse + historyBurn pulse Burn pulses + history Black mark synchronization enabled CR = IgnoredLF = Ignored On the paper Contents printouts shorter than the value specified by Determines what should control the page lengthFixed Document Mode. Shorter documents will automatically Be extended, while longer documents will be divided into Fixed Document Mode Length P37 P38 Sets max black mark length to 5 mm Sets min black mark length to 4 mmFeeds 50 mm between black mark and cut Add 30-mm top margin Eject page when new page is printed. Retract disabled Retract page when new page is printedDo nothing when new page is printed. Auto-eject and retract Will be retracted. Range 1-30, 1 step = 10 s Off Automatic Distance CalculationNo indication Paper Near End indication Default Parameter Settings Setup Printable Area N43 N44 Aligning Preprint And Thermal Print Recommended black mark size and position Setup Enables/disables black mark check Parameters Used Garbage, Black Mark and Out of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset At the End Of the Document Send→ Text and graphics Simple Calibration Process Black-Mark Sensing from Within Windows Interface Cable power USB Interface+ Data Cable ground Setup Options Serial Option, TTP Interface Maintenance Fault Finding Fault Finding 101 Cleaning The Print Head Printer with retract Fitting a Shutter Firmware Specifications Print Data None, Odd or Even Command Code Modes Non-Windows Applications Basic Character Set 108 109 Bar Codes Non-Windows Applications Paper Handling Printer Dimensions Environmental Conditions Paper Specification MiscellaneousGeneral Thermal coating Perforation Preprinting Print can be expected within a zone of approximately 2-mm Black Mark Size and PositionAround the edges of the hole. The function must be tested Part Number List AccessoriesPrinters 116 117 Roll Holders Roll Holder for Paper Rolls up to 150 mm 119 120 中国 RoHS 材料声明 China RoHS Material Declaration 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006标准规定的限量要求。 122 Index Numerics Status 57 Parameter store 53 Parameters Index Underline UPC Connector PortUSB Page Zebra Technologies Europe Limited