Retract page when new page is printed | Zebra Technologies TTP 7030

82

Default Parameter Settings

Print Setup

45	0	Default	Presenter Mode	DRV
45	0	Min	Presenter Mode	DRV
	230	Max

Sets the function of the presenter. The Retract selections are only valid if a retract option is fitted.

			<ESC>&P<45><0>	Eject page when new page is printed. (Retract disabled)
			<ESC>&P<45><3>	Eject page when new page is printed. Page not taken after 30s
				will be retracted. (Range 1-30, 1 step = 10 s)
			<ESC>&P<45><100>	Retract page when new page is printed
			<ESC>&P<45><103>	Retract page when new page is printed. Page not taken after 30s
				will be retracted. (Range 101-130, 1 step = 10 s)
			<ESC>&P<45><200>	Do nothing when new page is printed. (Auto-eject and retract
				disabled).
			<ESC>&P<45><203>	Do nothing when new page is printed. Page not taken after 30s
				will be retracted. (Range 201-230, 1 step = 10 s)
	40	Default
47	40	Default		Eject Calibration Constant	DRV
47	0	Min		Eject Calibration Constant	DRV
	255	Max

Sets the eject length of the printout, that is the length of paper that protrudes outside the printer after a cut command. This eject length should be 40-63 mm. Marks on the test printout show max and min eject length.

The default value when loading firmware is 40, but should be set individually from printer to printer. The set value is shown in a line on the test printout.

After sending the command, store the parameters, and wait until the presenter motor buzzes. Then make a self test printout to check if the set eject length is correct.

Example • This example sets parameter 47 to 50 and stores the parameters as default settings

<ESC>&P<47><50>

<ESC>&<4>

P1003636-002

TTP 7030™ Technical Manual

10/05/2009

Image 82

Zebra Technologies TTP 7030 Eject page when new page is printed. Retract disabled, Retract page when new page is printed

Contents

Zebra TTP P1003636-002 TTP 7030 Technical Manual 10/05/2009 Contents Programming Interface P1003636-002 TTP 7030 Technical Manual 10/05/2009 About This Manual IntroductionUpdating Contacts Mail address emb@zebra.com Subject line Emaillist Product Presentation Printer Exterior, Rear View Printer Exterior, Side View Status Indicator IndicatorsControl Board Indicators Feed Button Installation Installation Considerations Top view Electrostatic Discharges, and Earth Currents Ambient Light Using a Serial Adapter Connecting To The ComputerConnect the TTP Fitting a serial adapter to the printer Connecting the Power GND Is a power button available for the printer? Making a Test Printout Installing a Printer Driver Paper Level Sensor Indicators on Roll Holder Paper Level Sensors Paper-near-end Sensor Connection Operation Installing a Paper Roll Make sure the printer is turned on Angle Cut the paper in a suitable angle. See Figure Clearing Paper Jams Open the Print Module Programming Cursor will retain its last position on the ticket Text text How The Commands Are Described Two-Byte Character Definitions Therefore, the two-byte representation of 731 is Summary Of Control Codes & Escape Sequences 50 n1 27 5 80 n1 Parameter-setting data Enquiry 27 5 Head temperature Enquiry27 5 Bootware version Enquiry 27 5 Device ID Enquiry Software Command Syntax Black Mark Top-Of-Form Commands Changes the alignment of text and logotypes Text CommandsLeft Center Right Selects font Selects normal font font ESC ! 4 selects fontSelects font ESC ! 5 selects font Turns OFF Italics Normal Turns on Italics ESC T n1 Reversed/Inversed Text ESC w n1 Commands, are not cancelled Overprint the O ESC d n1 Make n Linefeeds Barcode Commands Samples of barcodes UPC Add-on. Two of five characters are allowed of the add-on Must be placed at the end of the bar code data Columns Error level, 0=auto, 1=Level0, 2=Level1, etcDot Height, sets mow many pixel lines each row consists Graphics Commands Determines the number of bytes. Range ESCr000000000000001193000024003 ESC g n1 Print Logotype Run presenter Print CommandsForm feed Clear presenter Print buffer full Press on FF-button ESC j n1 Paper Reverse To auto Cut And Present CommandsYou can also use RS together with the paper advance command Gives a cut & eject after the last text line Ejects the presented Retracts the presented ENQ System Related Commands Erases all logotypes stored in the flash Prom Erases all fonts stored in the flash Prom See Default Parameter Settings on Set several parameters at once Status Reporting Commands Paper-near-end Enquiry Read← Sensor Status Read←n Where n can be ‘A’ Ascii or 41 hex or 65 dec That is, a response with the value 129 indicates version That is, a response with the value 130 indicates version Under Summary Of Parameter Settings on One-byte marker. Range 1h to 255h Font Loading File Format Character bitmap data Logotypes Loading All logotypes are erased with the ESC&L command Printing Status Reporting Default Parameter Settings Programming Default Parameter Settings Default Value Summary Of Parameter Settings Serial Interface Set-Up Xon / Xoff Select what handshaking to use on the serial interfaceNo flow control Hardware No, paper out and error signals are not disabled Parallel Port SetupYes, paper out and error signals are disabled Current consumption Print SetupDisable the loop Cm loop Burn pulse Controls what the printer does with buffered dataBurn pulse + history Burn pulses + history LF = Ignored Black mark synchronization enabledCR = Ignored On the paper Fixed Document Mode. Shorter documents will automatically Contents printouts shorter than the value specified byDetermines what should control the page length Be extended, while longer documents will be divided into Fixed Document Mode Length P37 P38 Feeds 50 mm between black mark and cut Sets max black mark length to 5 mmSets min black mark length to 4 mm Add 30-mm top margin Do nothing when new page is printed. Auto-eject and retract Eject page when new page is printed. Retract disabledRetract page when new page is printed Will be retracted. Range 1-30, 1 step = 10 s No indication OffAutomatic Distance Calculation Paper Near End indication Default Parameter Settings Setup Printable Area N43 N44 Aligning Preprint And Thermal Print Recommended black mark size and position Setup Enables/disables black mark check Parameters Used Garbage, Black Mark and Out of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset At the End Of the Document Send→ Text and graphics Simple Calibration Process Black-Mark Sensing from Within Windows Interface + Data Cable powerUSB Interface Cable ground Setup Options Serial Option, TTP Interface Maintenance Fault Finding Fault Finding 101 Cleaning The Print Head Printer with retract Fitting a Shutter Firmware Specifications Print Data None, Odd or Even Command Code Modes Non-Windows Applications Basic Character Set 108 109 Bar Codes Non-Windows Applications Paper Handling Printer Dimensions Environmental Conditions General Paper SpecificationMiscellaneous Thermal coating Perforation Preprinting Print can be expected within a zone of approximately 2-mm Black Mark Size and PositionAround the edges of the hole. The function must be tested Part Number List AccessoriesPrinters 116 117 Roll Holders Roll Holder for Paper Rolls up to 150 mm 119 120 中国 RoHS 材料声明 China RoHS Material Declaration 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006标准规定的限量要求。 122 Index Numerics Status 57 Parameter store 53 Parameters Index Underline UPC Connector PortUSB Page Zebra Technologies Europe Limited