Manuals / Zebra Technologies / Computer Equipment / Printer

Zebra Technologies TTP 7030 Installing a Paper Roll, Make sure the printer is turned on

Models: TTP 7030

1 128

Download 128 pages 16.1 Kb

Page 24

24

Operation

Installing a Paper Roll

Installing a Paper Roll

1.Turn the new paper roll as shown. The paper should be inserted into the printer with the temperature-sensitive side up.

Figure 9 • Paper Roll Orientation

2.Tear off a full turn of the paper (approximately 0.5 m) from the new paper roll.

Caution • This is important since the outer end of the paper is usually fixed to the roll with some type of glue or self-adhesive substance that might otherwise cause paper jam or even print head damage.

Figure 10 • Tear off 0.5 m from the new paper rol

l

3.Make sure the printer is turned ON.

P1003636-002

TTP 7030™ Technical Manual

10/05/2009

Image 24

Zebra Technologies TTP 7030 technical manual Installing a Paper Roll, Make sure the printer is turned on

Contents

Zebra TTP P1003636-002 TTP 7030 Technical Manual 10/05/2009 Contents Programming Interface P1003636-002 TTP 7030 Technical Manual 10/05/2009 Introduction About This ManualUpdating Contacts Mail address emb@zebra.com Subject line EmaillistProduct Presentation Printer Exterior, Rear ViewPrinter Exterior, Side View Indicators Status IndicatorControl Board Indicators Feed Button Installation Installation Considerations Top viewElectrostatic Discharges, and Earth Currents Ambient LightConnecting To The Computer Using a Serial AdapterConnect the TTP Fitting a serial adapter to the printer Connecting the Power GNDIs a power button available for the printer? Making a Test PrintoutInstalling a Printer Driver Paper Level Sensor Indicators on Roll Holder Paper Level SensorsPaper-near-end Sensor Connection Operation Installing a Paper Roll Make sure the printer is turned onAngle Cut the paper in a suitable angle. See FigureClearing Paper Jams Open the Print ModuleProgramming Cursor will retain its last position on the ticketText text How The Commands Are Described Two-Byte Character Definitions Therefore, the two-byte representation of 731 isSummary Of Control Codes & Escape Sequences 27 5 Head temperature Enquiry 27 5 Bootware version Enquiry50 n1 27 5 80 n1 Parameter-setting data Enquiry 27 5 Device ID EnquirySoftware Command Syntax Black Mark Top-Of-Form CommandsText Commands Changes the alignment of text and logotypesLeft Center Right Selects normal font font ESC ! 4 selects font Selects font ESC ! 5 selects fontSelects font Turns OFF Italics Normal Turns on ItalicsESC T n1 Reversed/Inversed Text ESC w n1 Commands, are not cancelled Overprint the OESC d n1 Make n Linefeeds Barcode Commands Samples of barcodes UPC Add-on. Two of five characters are allowed of the add-on Must be placed at the end of the bar code dataError level, 0=auto, 1=Level0, 2=Level1, etc ColumnsDot Height, sets mow many pixel lines each row consists Graphics Commands Determines the number of bytes. RangeESCr000000000000001193000024003 ESC g n1 Print Logotype Print Commands Form feed Clear presenterRun presenter Print buffer full Press on FF-buttonESC j n1 Paper Reverse Cut And Present Commands You can also use RS together with the paper advance commandTo auto Gives a cut & eject after the last text lineEjects the presented Retracts the presentedENQ System Related Commands Erases all logotypes stored in the flash PromErases all fonts stored in the flash Prom See Default Parameter Settings on Set several parameters at onceStatus Reporting Commands Paper-near-end Enquiry Read← Sensor Status Read←n Where n can be ‘A’ Ascii or 41 hex or 65 dec That is, a response with the value 129 indicates versionThat is, a response with the value 130 indicates version Under Summary Of Parameter Settings on One-byte marker. Range 1h to 255h Font Loading File FormatCharacter bitmap data Logotypes LoadingAll logotypes are erased with the ESC&L command PrintingStatus Reporting Default Parameter Settings Programming Default Parameter Settings Default ValueSummary Of Parameter Settings Serial Interface Set-Up Select what handshaking to use on the serial interface No flow controlXon / Xoff HardwareParallel Port Setup No, paper out and error signals are not disabledYes, paper out and error signals are disabled Print Setup Disable the loopCurrent consumption Cm loopControls what the printer does with buffered data Burn pulse + historyBurn pulse Burn pulses + historyBlack mark synchronization enabled CR = IgnoredLF = Ignored On the paperContents printouts shorter than the value specified by Determines what should control the page lengthFixed Document Mode. Shorter documents will automatically Be extended, while longer documents will be divided intoFixed Document Mode Length P37 P38Sets max black mark length to 5 mm Sets min black mark length to 4 mmFeeds 50 mm between black mark and cut Add 30-mm top marginEject page when new page is printed. Retract disabled Retract page when new page is printedDo nothing when new page is printed. Auto-eject and retract Will be retracted. Range 1-30, 1 step = 10 sOff Automatic Distance CalculationNo indication Paper Near End indicationDefault Parameter Settings Setup Printable Area N43 N44Aligning Preprint And Thermal Print Recommended black mark size and positionSetup Enables/disables black mark check Parameters UsedGarbage, Black Mark and Out of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset At the End Of the Document Send→ Text and graphicsSimple Calibration Process Black-Mark Sensing from Within Windows Interface Cable power USB Interface+ Data Cable groundSetup Options Serial Option, TTPInterface Maintenance Fault Finding Fault Finding101 Cleaning The Print Head Printer with retract Fitting a ShutterFirmware Specifications Print Data None, Odd or EvenCommand Code Modes Non-Windows Applications Basic Character Set108 109 Bar Codes Non-Windows Applications Paper HandlingPrinter Dimensions Environmental ConditionsPaper Specification MiscellaneousGeneral Thermal coatingPerforation PreprintingBlack Mark Size and Position Print can be expected within a zone of approximately 2-mmAround the edges of the hole. The function must be tested Accessories Part Number ListPrinters 116 117 Roll Holders Roll Holder for Paper Rolls up to 150 mm119 120 中国 RoHS 材料声明 China RoHS Material Declaration 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006标准规定的限量要求。122 Index NumericsStatus 57 Parameter store 53 Parameters Index Connector Port Underline UPCUSB Page Zebra Technologies Europe Limited