Samples of barcodes | Zebra Technologies TTP 7030 instruction

Programming

Barcode Commands

Figure 16 • Samples of barcodes

.

41

Selecting code 128 and starting the data string with FNC1 generates an EAN128 code.

10/05/2009

TTP 7030™ Technical Manual

P1003636-002

Image 41

Zebra Technologies TTP 7030 technical manual Samples of barcodes

Contents

Zebra TTP P1003636-002 TTP 7030 Technical Manual 10/05/2009 Contents Programming Interface P1003636-002 TTP 7030 Technical Manual 10/05/2009 Updating IntroductionAbout This Manual Mail address emb@zebra.com Subject line Emaillist Contacts Printer Exterior, Rear View Product Presentation Printer Exterior, Side View Control Board Indicators IndicatorsStatus Indicator Feed Button Installation Top view Installation Considerations Ambient Light Electrostatic Discharges, and Earth Currents Connect the TTP Connecting To The ComputerUsing a Serial Adapter Fitting a serial adapter to the printer GND Connecting the Power Making a Test Printout Is a power button available for the printer? Installing a Printer Driver Paper Level Sensors Paper Level Sensor Indicators on Roll Holder Paper-near-end Sensor Connection Operation Make sure the printer is turned on Installing a Paper Roll Cut the paper in a suitable angle. See Figure Angle Open the Print Module Clearing Paper Jams Cursor will retain its last position on the ticket Programming Text text How The Commands Are Described Therefore, the two-byte representation of 731 is Two-Byte Character Definitions Summary Of Control Codes & Escape Sequences 27 5 Bootware version Enquiry 27 5 Head temperature Enquiry50 n1 27 5 80 n1 Parameter-setting data Enquiry 27 5 Device ID Enquiry Black Mark Top-Of-Form Commands Software Command Syntax Left Center Right Text CommandsChanges the alignment of text and logotypes Selects font ESC ! 5 selects font Selects normal font font ESC ! 4 selects fontSelects font Turns OFF Italics Normal Turns on Italics ESC T n1 Reversed/Inversed Text ESC w n1 Overprint the O Commands, are not cancelled ESC d n1 Make n Linefeeds Barcode Commands Samples of barcodes UPC Must be placed at the end of the bar code data Add-on. Two of five characters are allowed of the add-on Dot Height, sets mow many pixel lines each row consists Error level, 0=auto, 1=Level0, 2=Level1, etcColumns Determines the number of bytes. Range Graphics Commands ESCr000000000000001193000024003 ESC g n1 Print Logotype Form feed Clear presenter Print CommandsRun presenter Print buffer full Press on FF-button ESC j n1 Paper Reverse You can also use RS together with the paper advance command Cut And Present CommandsTo auto Gives a cut & eject after the last text line Retracts the presented Ejects the presented ENQ Erases all logotypes stored in the flash Prom System Related Commands Erases all fonts stored in the flash Prom Set several parameters at once See Default Parameter Settings on Status Reporting Commands Paper-near-end Enquiry Read← Sensor Status That is, a response with the value 129 indicates version Read←n Where n can be ‘A’ Ascii or 41 hex or 65 dec That is, a response with the value 130 indicates version Under Summary Of Parameter Settings on One-byte marker. Range 1h to 255h File Format Font Loading Character bitmap data Loading Logotypes Printing All logotypes are erased with the ESC&L command Status Reporting Default Parameter Settings Programming Default Value Default Parameter Settings Summary Of Parameter Settings Serial Interface Set-Up No flow control Select what handshaking to use on the serial interfaceXon / Xoff Hardware Yes, paper out and error signals are disabled Parallel Port SetupNo, paper out and error signals are not disabled Disable the loop Print SetupCurrent consumption Cm loop Burn pulse + history Controls what the printer does with buffered dataBurn pulse Burn pulses + history CR = Ignored Black mark synchronization enabledLF = Ignored On the paper Determines what should control the page length Contents printouts shorter than the value specified byFixed Document Mode. Shorter documents will automatically Be extended, while longer documents will be divided into Length P37 P38 Fixed Document Mode Sets min black mark length to 4 mm Sets max black mark length to 5 mmFeeds 50 mm between black mark and cut Add 30-mm top margin Retract page when new page is printed Eject page when new page is printed. Retract disabledDo nothing when new page is printed. Auto-eject and retract Will be retracted. Range 1-30, 1 step = 10 s Automatic Distance Calculation OffNo indication Paper Near End indication Default Parameter Settings Setup N43 N44 Printable Area Recommended black mark size and position Aligning Preprint And Thermal Print Setup Parameters Used Enables/disables black mark check Garbage, Black Mark and Out of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Send→ Text and graphics At the End Of the Document Simple Calibration Process Black-Mark Sensing from Within Windows Interface USB Interface Cable power+ Data Cable ground Serial Option, TTP Setup Options Interface Maintenance Fault Finding Fault Finding 101 Cleaning The Print Head Fitting a Shutter Printer with retract Firmware Specifications None, Odd or Even Print Data Basic Character Set Command Code Modes Non-Windows Applications 108 109 Paper Handling Bar Codes Non-Windows Applications Environmental Conditions Printer Dimensions Miscellaneous Paper SpecificationGeneral Thermal coating Preprinting Perforation Around the edges of the hole. The function must be tested Black Mark Size and PositionPrint can be expected within a zone of approximately 2-mm Printers AccessoriesPart Number List 116 117 Roll Holder for Paper Rolls up to 150 mm Roll Holders 119 120 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006标准规定的限量要求。中国 RoHS 材料声明 China RoHS Material Declaration 122 Numerics Index Status 57 Parameter store 53 Parameters Index USB Connector PortUnderline UPC Page Zebra Technologies Europe Limited