Chapter 11 Telnet

 

 

 

 

 

 

Table 50 Generic Telnet Commands (continued)

 

 

 

COMMANDS

ARGUMENTS

DESCRIPTION

 

[ ] IS OPTIONAL

 

 

 

 

 

dir

 

Show details of files in the flash ROM, including the

 

 

 

working area and upload area. The listed

 

 

 

filenames are:

 

 

 

•

bootcode: boot loader

 

 

 

•

sysfw4m: system firmware

 

 

 

• G2C44H2xM: ermination system EoC driver

 

 

 

• G2C44H2xEp: EP(3210) EoC driver

 

 

 

• G3C1244xEp: EP(3310) EoC driver

 

 

 

• diagsw: diagnosis utility file

 

 

 

Details shown include the file id, file version, file

 

 

 

date, and file size.

 

 

 

 

 

dns

[-s <pri/sec> <ip>]

Display or setup DNS server settings.

 

 

 

• -s pri <ip>: setup Primary DNS server's IP

 

 

 

• -s sec <ip>: setup Secondary DNS server's IP

 

 

 

 

 

exit

 

Close the Telnet console.

 

 

 

 

 

quit

 

Close the Telnet console.

 

 

 

 

 

ep

[-c <hostcnt>]

Setup termination adapter EoC properties.

 

 

[-n <note>]

• <hostcnt>: termination adapter Host Limit

 

 

-m <mac>

 

(0~12), default 3

 

 

• <note>: termination adapter Note

 

 

 

• <mac>: The EoC MAC address of the

 

 

 

 

termination adapter being configured.

 

 

 

 

 

ephpnareboot

-m <mac>

Reset termination adapter EoC device

 

 

 

 

 

epreg

-m <mac>

Add a termination adapter profile, (like Add EP in

 

 

 

the Web Configurator)

 

 

 

 

 

eprestore

-m <mac>

Apply termination adapter EoC/Ethernet properties

 

 

 

(settings in termination system) to a termination

 

 

 

adapter, (like ReConfig EP in the Web

 

 

 

Configurator).

 

 

 

 

 

epstat

-m <mac>

Display termination adapter LAN1/LAN2/EoC port

 

 

[-r]

statistics.

 

 

• -r: reset all port statistics counters to 0.

 

 

 

 

 

 

 

 

epswc

-m <mac>

Display or setup the Ethernet properties of a

 

 

[-t]

termination adapter’s built-in switch.

 

 

• -t: display termination adapter switch settings

 

 

[-u]

 

 

• -u: display termination adapter switch/port

 

 

 

 

 

[-r]

 

status

 

 

• -r: reset termination adapter switch

 

 

 

 

 

[-d]

• -d: reset termination adapter switch settings to

 

 

[-p <lan1/lan2/hpna> [-l <up/

 

factory defaults

 

 

• -p: configure termination adapter LAN1/LAN2/

 

 

down>] [-s <auto /10h /10f /100h /

 

EoC port

 

 

100f>] [-f <on/off>]]

• -l: link, <up/down>: force current port to link

 

 

 

 

up or down, i.e. enable/disable current port

 

 

 

• -s: current port Ethernet mode setting,

 

 

 

 

<auto>: auto-negotiation mode

 

 

 

 

<10h/10f/100h/100f>: 10/100Mbps, half/full-

 

 

 

 

duplex mode

 

 

 

• -f: current port Ethernet flow-control setting,

 

 

 

 

<on/off>: turn on /off flow control

 

 

 

 

 

 

63

EOC350 Series User’s Guide