Ryobi RY64400 Fueling and Refueling the Cultivator, Oxygenated Fuels, Applications, See Figures 8

OPERATION

Always use a 4-stroke motor lubricant that meets or exceeds the requirements for API service classification SJ. Check lubricant level before each use.

NOTE: Non-detergent or 2-stroke engine lubricants will damage the engine and should not be used.

To add engine lubricant:

Remove the cap and seal from lubricant bottle provided.

Unscrew the oil cap/dipstick and remove.

Using a funnel add entire bottle of engine lubricant through oil fill hole.

Reinstall the oil cap/dipstick and secure.

To check engine lubricant level:

Set cultivator in upright position with the wheel assembly connected for stability.

Wipe dipstick clean and re-seat in hole; do not rethread.

Remove dipstick again and check lubricant level. Lubricant level should fall within the hatched area on the dipstick.

If level is low, add engine lubricant until the fluid level rises to the upper portion of the hatched area on the dipstick.

Replace and secure the oil cap/dipstick.

CAUTION:

Do not overfill. Overfilling the crankcase may cause ­excessive smoke, oil loss, and engine damage.

WARNING:

Gasoline and its vapors are highly flammable and ex- plosive. To prevent serious personal injury and property damage, handle it with care. Keep away from ignition sources and open flames, handle outdoors only, do not smoke while mixing gasoline and lubricant together; and wipe up spills immediately.

FUELING AND REFUELING THE CULTIVATOR

See figure 7.

Clean surface around fuel cap to prevent contamination.

Loosen fuel cap slowly. Rest the cap on a clean surface.

Carefully pour fuel into the tank. Avoid spillage.

Prior to replacing the fuel cap, clean and inspect the gasket.

Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage.

NOTE: It is normal for smoke to be emitted from a new engine after first use.

WARNING:

Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting engine. Do not smoke and stay away from open flames and sparks! Failure to follow these instructions could result in serious personal injury.

OXYGENATED FUELS

DO NOT USE E85 FUEL. IT WILL VOID YOUR WARRANTY.

NOTE:  Fuel system damage or performance problems re- sulting from the use of an oxygenated fuel containing more than the percentages of oxygenates stated below are not covered under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume (commonly referred to as E10) is acceptable. E85 is not.

APPLICATIONS

Before each use, inspect the entire product for damaged, missing, or loose parts such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product until all missing or damaged parts are replaced. Please call 1-800-860-4050 or contact an authorized service center for assistance.

You may use this product for the purposes listed below:

nBreaking up garden soil to prepare seed bed for planting

nShallow cultivating to remove weeds

Edging around walkways, flower beds and other similar areas.

STARTING/STOPPING THE CULTIVATOR

See Figures 8 - 11.

To start an engine that is cold or has run dry:

nFill the fuel tank, if necessary. Always use the proper gasoline.

nPlace the on/stop switch in the ON (  ) position.

NOTE: Do not engage the throttle trigger during the starting process.

nPress the primer bulb 10 times slowly.

NOTE: After the 7th press, fuel should be visible in the primer bulb. If it is not, continue to press the primer until you see fuel in the bulb.

nLean the unit back on its wheels so that the handlebar rests on the ground.

nPlace foot on handle bar and one hand on front handle.

nSet the choke lever to the FULL CHOKE position.

nWith the throttle trigger at idle, pull starter handle sharply until engine attempts to run. Do not pull the starter handle more than four (4) times.

8 - English