Remington EL-8: 107624-01, EL-8: 107624-02, EL-8: 107625-01, EL-8: 107625-02, EL-8: 111174-01

Page 19

OPERATING CHAIN SAW

Continued

LIMBING A TREE

WARNING: Avoid kickback. Kick- back can result in severe injury or death. See Kickback, page 3, to avoid risk of kickback.

WARNING: When cutting limb that is under tension, use extreme caution. Be alert for wood springing back. When wood tension is released, limb could spring back and strike operator causing severe injury or death.

Limbing is removing branches from a fallen tree. Make sure your footing is Þrm. Keep feet apart. Di- vide your weight evenly on both feet. Do not remove larger limbs under tree that support log off ground. Remove each limb with one cut (see Figure 14). Clear cut limbs from work area often. This will help main- tain a safe work area.

Make sure you start your cut where limb will not pinch saw during cutting. To avoid pinching, start cut on freely hanging limbs from above limb. Start cut on limbs under tension from under limb. If pinch occurs, turn saw off, lift limb, and remove saw.

Bucking a log is cutting a log into sections. Make sure your footing is Þrm. Keep feet apart. Divide your weight evenly on both feet. When possible, raise log or section off ground. Do this by using limbs, logs, chocks, etc. When cutting through log, maintain control by re- ducing cutting pressure near end of cut. Do not relax your grip on chain saw handles. Do not let moving chain touch ground. Ground will dull moving chain. After cutting through log, release trigger to turn saw off before moving saw.

Follow directions below to buck a log.

Entire Length Of Log On Ground

Cut log from top (see Figure 15).

Log Supported On One End

1.Make Þrst cut on underside of log (see Figure 16). Use top of guide bar to make this cut. Cut 1/3 through diameter of log. This cut will keep sec- tion from splintering when cut.

2.Make second cut directly above Þrst cut. Cut down to meet Þrst cut. This cut will keep log from pinching guide bar and chain.

Log Supported On Both Ends

1.Make Þrst cut from above log (see Figure 17). Cut 1/3 through diameter of log. This cut will keep section from splintering when cut.

2.Make second cut on underside of log, directly under Þrst cut. Use top of guide bar to make this cut. Cut up to meet Þrst cut. This will keep log from pinching guide bar and chain.

BUCKING A LOG

WARNING: Avoid kickback. Kick- back can result in severe injury or death. See Kickback, page 3, to avoid risk of kickback.

WARNING:

¥If on slope, make sure log will not roll down hill. Secure log by using wooden stakes. Drive wooden stakes into ground on downhill side of log. Stand on uphill side of log while cutting. Log may roll after cutting.

¥Never try cutting through two logs at same time. This could

increase the risk of kickback.

¥While cutting log, never hold log with your hand, leg, or foot.

¥While cutting log, never allow another person to hold log.

¥Turn off and unplug saw before mov- ing from one place to another.

TRIMMING A TREE (PRUNING)

WARNING: Avoid kickback. Kick- back can result in severe injury or death. See Kickback, page 3, to avoid risk of kickback.

WARNING: Do not operate chain saw while

¥in a tree

¥on a ladder or any other unstable sur- face

¥in any awkward position

You may lose control of saw causing severe injury.

WARNING: Do not cut limbs higher than your shoulders.

CAUTION: Seek professional help if facing conditions beyond your ability.

Continued

107705

19

www.desatech.com

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Listed Manual Para EL Usuario Manuel D’UTILISATION ET D’ENTRETIENRead ALL Instructions Important Safety InformationBefore Operating SAW While Operating SAWSaw Maintenance and Kickback Safety Kickback Safety Devices On This SawKickback Maintenance and Storage of Chain SAW LEA Todas LAS Instrucciones Información Importante DE SeguridadAntes DE Utilizar LA Sierra ¥ in a dry place¥ con el dedo fuera del gatillo AL Utilizar LA SierraContragolpes Lleve la sierra elŽctrica de un lugar a otroMantenimiento Y Almacenamiento DE SU Sierra ELƒCTRICA Mantenimiento de la cadena y seguridad contra contragolpesCuide de su sierra elŽctrica ¥ Nunca la exponga a la lluvia ¥ lorsquon est pressŽ Consignes DE Sécurité ImportantesAvant Dõutiliser LA TRON‚ONNEUSE Pendant Lutilisation DE LA TRON‚ONNEUSESuite Entretien de la trononneuse et protection contre le recul ReculEntretien ET Remisage DE LA TRON‚ONNEUSE ¥ Garder vis et Žcrous bien serrŽs FIGURES/FIGURAS/FIGURESFIGURES/FIGURAS/ Figures FIGURES/FIGURAS Bucking Log When Log Is Supported On One End Guide Bar Cross Section Showing Uneven Bar Wear Models EL-8 107624-01 107625-01, 107625-02 Electric Chain SAWUnpacking Chain SAW Names and TermsSAW Chain Tension Adjustment AssemblyImportant Do not clamp chain saw in vise during assembly Oiling Chain Filling OIL TankOperating Chain SAW Extension CordsFelling Cut Felling Procedure Felling NotchFelling a Tree Cutting Down a Tree Before Felling a TreeBucking a LOG Limbing a TreeTrimming a Tree Pruning Sharpening SAW Chain Cleaning MaintenanceCleaning SAW Body Care of Guide BARStorage Technical ServiceIllustrated Parts List Replacement Parts and Accessories Repair ServiceObserved Fault Possible Cause Remedy TroubleshootingIndustries of Canada, Inc Electric Chain SAW Limited WarrantyEnsamblaje Sierra EléctricaDesembalaje TerminologíaAjuste DE Tensión DE LA Cadena Serrada USO DE LA Sierra Eléctrica LubricaciónTala final Tala DE UN çRBOL Derribamiento de un ‡rbolAntes de derribar un ‡rbol Procedimiento de tala Corte de la muescaCorte el tronco comenzando por arriba vea la Figura Desmembramiento DE UN çRBOLTrozado DE UN Tronco La totalidad del tronco sobre el sueloPoda DE UN çRBOL Limpieza Y MantenimientoTronco apoyado en un extremo Tronco apoyado sobre ambos extremosAfilado DE LA Cadena Accesorios Y Piezas DE Repuesto AlmacenamientoServicio Técnico Lista Ilustrada DE PartesServicio Durante LA GARANTêA Servicio DE ReparacionesServicio Fuera DE GARANTêA Falla Observada Causa Posible Diagnóstico Y Resolución DE ProblemasSOLUCIîN GARANTêA Limitada DE Sierra ELƒCTRICA Información DE GarantíaMontage Tronçonneuse Électrique PrimeDéballage Vocabulaire DE LA TronçonneuseRemplissage DU Réservoir D’HUILE Réglage DE LA Tension DE LA ChaîneSystme de lubrification automatique Utilisation DE LA TronçonneuseRallonges ƒLECTRIQUES Lubrification DE LA CHAëNE Systme de lubrification manuelTrait dÕabattage Abattage Dõun ArbreAvant dÕabattre un arbre ProcŽdure dÕabattage Sifflet dÕabattageLa bille est soutenue ˆ une extrŽmitŽ ƑBRANCHAGETRON‚ONNAGE Dõune Bille Toute la bille repose au solEntretien DE LA GUIDE-CHAëNE Nettoyage ET EntretienTaille Dõun Arbre ƒlagage Nettoyage DU Carter DE TRON‚ONNEUSERemisage Réparations Service TechniquePièces DE Rechange ET Accessoires Liste DE Pièces IllustréesREMéDE DépannageDƒFAILLANCE OBSERVƒE Cause PossibleConserver Cette Garantie Information SUR LA GarantieGarantie LIMITƒE Pour LA TRON‚ONNEUSE ƒLECTRIQUE Parts Company of America Replacement PARTS/PARTES DE REPUESTO/ Pièces DE RechangeMODELS/MODELOS/MODéLES 107624-01 Renvoi Parts LIST/LISTA DE REPUESTOS/LISTE DES PiècesMODELS/MODELOS/MODéLES 107625-01, 107625-02 CLAVE/N DE Parte Continœa/Ë suivre 107705 107705-01 Rev. K 02/03

EL-8: 107624-01, EL-8: 107624-02, EL-8: 107625-01, EL-8: 107625-02, EL-8: 111174-01 specifications

The Remington EL-8 is an innovative line of electric shavers that have caught the attention of grooming aficionados for their precision, technology, and user-friendly design. Within this series, the models EL-8: 107624-01, EL-8: 107624-02, EL-8: 107625-01, EL-8: 107625-02, and EL-8: 111174-01 stand out due to their unique characteristics and features that cater to diverse shaving needs.

The EL-8: 107624-01 is noted for its ergonomic design, which makes it comfortable to hold and easy to manoeuvre. It employs dual blade technology that delivers a close and seamless shave, minimizing skin irritation. This model also features a pivoting head that adapts to the contours of the face, providing an efficient shave even in hard-to-reach areas.

The EL-8: 107624-02 mirrors many of the conveniences of the 107624-01, but it introduces a built-in LED display that provides users with battery status and cleaning notifications. This added tech feature ensures that the shaver remains in peak condition, while its waterproof design allows for easy cleaning under running water, adding to the convenience factor.

Moving on to the EL-8: 107625-01, this model comes with a unique skin protector technology that reduces razor burn during shaving. It is designed with hyper-flex technology that allows for multidirectional movement of the blades, ensuring that every hair is captured in one pass. The synergistic combination of advanced blade design and patented skin protection makes this a top choice for sensitive skin types.

The EL-8: 107625-02 continues the trend by incorporating a fast-charging feature. It can fully charge in under an hour for extensive battery life, making it a reliable option for on-the-go grooming. The smart sensing capability adjusts power based on hair density, further enhancing the overall shave experience.

Lastly, the EL-8: 111174-01 introduces a luxurious touch with its sleek design and premium materials. This model emphasizes a high-performance motor that offers powerful and consistent performance, along with noise reduction technology to create a more pleasant shaving experience. It also features a convenient travel lock, making it ideal for those who travel frequently.

In summary, the Remington EL-8 series—encompassing models 107624-01, 107624-02, 107625-01, 107625-02, and 111174-01—effectively balances advanced technology with user comfort, offering a personalized grooming experience that meets the varying needs of today's modern man. With their combination of innovative features, these shavers redefine the standard for electric shaving, making each user feel confident and at ease.
Top Page Image Contents